• Contact

Filter Results




Product Brands

Product Types

Product Applications

MARKETS

Clear All

Selected Filters:


  • A/D Firefilm III

    Features:

    • UL/ULC, ITS, ICC-ES and FM Listed – designs for many types of steel sections. Up to 3 hour fire ratings for both interior general purpose and interior conditioned space applications.
    • Decorative Finish – Gives a smooth, decorative finish. Compatible topcoats available in a wide range of colors.
    • Advanced fiber free formulation - dust free surface.
    • Durable finish – Provides a hard, impact and abrasion resistant surface.
    • Topcoat finishes smooth to slight orange peel.
    • Thin film coating – space saving smaller column footprints.
    • Low VOC content.
    • LEED compliant

    Description:

    A/D Firefilm® III is a decorative, fiber free, thin film intumescent coating designed for the fire protection of steelwork for up to a 3 hour fire rating, depending on the design. The recommended use for this product is fireproofing of interior steel beams, columns, tubes, and pipes.


  • Bitumastic 300 M

    Features:

    • Excellent chemical, corrosion and abrasion resistance
    • High-build, 16-24 mils (400-610 microns) in a single coat (up to 35 mils with force curing)
    • Compatible with controlled cathodic protection
    • Suitable for use in exposures as referenced in the following specifications:
    • Corp of Engineers C-200, C200a
    • AWWA C-210 for exterior
    • SSPC-Paint 16
    • Steel Tank Institute Corrosion Control System STI-P3

    Description:

    Renowned high build coal tar epoxy polyamide for protection of steel and concrete in single or two-coat applications in a broad variety of aggressive industrial applications.


  • Bitumastic 50

    Features:

    • Application up to 30 dry mils (750 microns) in a single coat
    • Self priming, single-coat capabilities
    • Excellent corrosion resistance
    • Complies with MIL-C-18480-B and Bureau of Reclamation CA50 specifications

    Description:

    Ultra-high build, single-component coal tar mastic for protecting steel and concrete substrates subject to aggressive conditions and for below grade damp proofing requirement


  • Carbocoat 115

    Features:

    • Rapid cure
    • VOC compliant for most areas
    • Good for filling properties on rough and pitted steel
    • Fast dry to handle properties

    Description:

    Fast drying steel primer that provides corrosion protection on structural steel. Well suited for fabrication shops that need fast cure to dry and handle times. May be topcoated with conventional alkyds or acrylics for color, aesthetics or additional protection.


  • Carbocoat 150 Universal Primer

    Features:

    • Good for extended exposure demands
    • Ability to be welded through
    • Heavy-metal free
    • VOC compliant for most areas
    • Accepts wide range of topcoats

    Description:

    Heavy-duty primer formulated to provide long term protection of structural steel. It provides excellent adhesion and can be welded through to yield sound welds.


  • Carbocoat OEM Universal Primer

    Features:

    • Good for extended exposure demands
    • Ability to be welded through
    • Heavy-metal free
    • VOC compliant for most areas

    Description:

    Heavy-duty primer formulated to provide long term protection of structural steel. It provides excellent adhesion and can be welded through to yield sound welds.


  • Carbocrylic 1295 HS

    Features:

    • Offers excellent corrosion and weathering protection.
    • NORSOK Approved for offshore
    • Recommended for chemical industry, offshore, power and heavy industry.

    Description:

    Carbocrylic is a high solids topcoat with good weathering capabilities. Offers a glossy, smooth, hard finish that is easy cleanable. One coat application capable.


  • Carbocrylic 3350

    Features:

    • Excellent performance over inorganic zinc primers
    • Superior color and gloss retention
    • Single component
    • Spray, brush and roll
    • Low odor, low VOC
    • Very good filling properties for masonry surfaces

    Description:

    Versatile coating with excellent performance properties. Frequently used in the bridge market as a finish coat over inorganic zinc primers, as well as a user-friendly finish for numerous other substrates. In off-white formula may be used as a block-filler.


  • Carbocrylic 3358

    Features:

    • Single component
    • Resistant to flash rusting
    • Outstanding corrosion protection
    • Low odor, low VOC

    Description:

    Surface tolerant direct-to-metal primer with excellent corrosion resistant properties, resistance to flash rusting and suitability for SPPC-SP2 and SP3-cleaned steel.


  • Carbocrylic 3359

    Features:

    • Multi-purpose interior/exterior coating
    • Excellent color and gloss retention
    • Single component
    • Outstanding corrosion protection
    • Low odor, low VOC
    • Acceptable for use in USDA facilities

    Description:

    Versatile high performance finish with excellent corrosion resistance and exterior weathering properties.


  • Carbocrylic 3359 DTM

    Features:

    • Smooth, attractive, high build finish
    • Excellent weatherability, gloss and color retention
    • Low odor
    • Excellent corrosion protection
    • Meets most VOC (Volatile Organic Content) regulations
    • Excellent resistance to flash rusting
    • Outstanding application characteristics
    • Dry-fall* properties
    • Suitable for use in USDA inspected facilities

    Description:

    A single-component durable, high performance direct-to-metal acrylic coating for use where excellent weathering properties and chemical resistance are required. Use as a direct-to-metal acrylic coating for tank exteriors, piping, and structural steel, as well as other exterior and interior uses. May also be used as a finish coat over recommended primers.


  • Carbocrylic 3359 DTMC

    Features:

    • Smooth, attractive, high build finish
    • Excellent weatherability, gloss and color retention
    • Low odor
    • Excellent corrosion protection
    • Meets most VOC regulations
    • Excellent resistance to flash rusting
    • Outstanding application characteristics
    • Dry-fall* properties

    Description:

    A single component durable, high performance direct-to-metal acrylic coating for use where excellent weathering properties and chemical resistance are required. Use as a direct-to-metal acrylic coating for light to medium duty service on tank exteriors, piping, and structural steel. May also be used as a finish coat over recommended primers.


  • Carbocrylic 3359 Flat

    Features:

    • Multi-purpose interior/exterior coating
    • Excellent color retention
    • Single component
    • Outstanding corrosion protection
    • Low odor, low VOC

    Description:

    Versatile high performance finish with excellent corrosion resistance and exterior weathering properties, as well as suitability for interior and mild environments.


  • Carboglas 1601 SG

    Features:

    • Outstanding marine exposure resistance (atmospheric, tidal, subsea)
    • Excellent resistance to both organic and mineral acids
    • Excellent abrasion and impact resistance
    • Excellent resistance to bleach solutions and free chlorine
    • Outstanding long-term protection

    Description:

    This extremely durable and chemically resistant cladding utilizes a multi-step curing process that incorporates chemically-fused glass flake reinforcing in a highly cross-linked polyester matrix. The resultant layer is an extremely durable barrier against a variety of exposures including marine, fresh water, salt water, both mineral and organic acids, bleach solutions, and free chlorine. The multi-layer glass-flake reinforcement greatly impedes the penetration of water and other corrosives making this system extremely long performing.


  • Carboguard 1207

    Features:

    • Superior abrasion resistance
    • Excellent resistance to aerated seawater and various other chemicals
    • Excellent immersion performance
    • Easy to repair
    • VOC compliant to current AIM regulations

    Description:

    Ultra-durable solvent-free coating for use on steel and concrete substrates subject to severe impact and physical abuse. This aggregate filled coating offers exceptional abrasion resistance in heavy-duty marine and splash zone environments. It is ideal for high abuse areas on offshore structures exposed to aerated sea water (splash zone), boat landing areas, or working decks, lay down areas, helidecks, or walkways. It can be also be used for buried pipe due to its outstanding physical durability. Consult Carboline Tech Service for high profile non-skid applications.


  • Carboguard 1209

    Features:

    • Excellent abrasion resistance
    • Excellent chemical resistance
    • Outstanding impermeability
    • Single coat, self-priming capabilities
    • VOC compliant to current AIM regulations
    • Non-skid surface (optional)

    Description:

    Dense, highly impermeable glass flake-filled coating used for protecting steel and concrete. This versatile coating provides an impenetrable film for severe exposures in marine, offshore, petrochemical, pulp and paper and other aggressive environments. Optional use of light or course grit fillers provides nonskid properties.


  • Carboguard 1340

    Features:

    • Exceptional wetting characteristics
    • Low stress, highly flexible film
    • Very high solids
    • Low odor
    • User-friendly brush & roller application
    • VOC compliant to current AIM regulations

    Description:

    Penetrating primer/sealer for use on concrete substrates and Carboline Pyrocrete Fireproofing products. It performs extremely well in sealing cementitious surfaces and is designed to receive a variety of different generic types of finish coats. Some recommended uses of 1340 include the use as a curing compound or form release agent. When applied to “green” concrete it will retard the escape of moisture during the cure period. It is also excellent for use as a form release coating on plywood or steel forms.


  • Carboguard 1340 FC

    Features:

    • Excellent penetration and sealing action on masonry surfaces
    • Excellent adhesion to old coatings
    • Cures down to 35°F (2°C)
    • Low odor
    • Compatible with a variety of finish coat

    Description:

    Carboguard 1340 FC is a primer/sealer recommended for bare masonry and other substrates requiring sealing prior to coating application. This high solids, low VOC product has excellent penetration and sealing properties on many substrates. Carboguard 1340 FC cures fast in cold weather and is recommended as an alternative to Carboguard 1340 in such conditions. Use standard 1340 above 70°F.


  • Carboguard 1340N

    Features:

    • Exceptional wetting characteristics
    • Low stress, highly flexible film
    • Very high solids
    • Low odor
    • User-friendly brush & roller application
    • VOC compliant to current AIM regulations
    • Suitable for use in Nuclear Service Level 1

    Description:

    Penetrating primer/sealer for use on concrete substrates. It is a nuclear grade, DBA tested and certified for use in Nuclear Level 1 areas in a variety of systems with appropriate finish coats.


  • Carboguard 163

    Features:

    • Excellent adhesion to prepared steel & concrete surfaces
    • Excellent abrasion resistance
    • Excellent flexibility; will withstand the expansion and contraction effect encountered in large storage/processing facilities
    • Does not require a primer or a topcoat (self-priming)
    • Designed for application using plural component, airless spray equipment

    Description:

    A high-build, modified epoxy lining with good overall chemical resistance and versatility. It is can be used as a “caulk” for application in tanks for transition areas; floors and walls, lap welds, pitted steel; bolts; etc. It is ideal for the relining or reconditioning of older tanks. It has excellent flexibility and its spray-applied capability (plural component) makes it unique over other similar products that usually require hand lay-up/trowel application. Carboguard 163 can be used as a barrier coat for concrete or steel surfaces that are exposed to moderately corrosive environments. Applications include floors, piping, storage, tanks, and process vessels in oil refineries, chemical processing, and wastewater treatment plants.


  • Carboguard 235 HAR

    Features:

    • High abrasion resistance
    • Surface tolerant properties
    • Fast and low-temperature cure
    • Outstanding as a heavy duty hull coating for marine

    Description:

    Carboguard 235 HAR is a high abrasion resistant phenalkamine modified, surface-tolerant, epoxy specially formulated for application in marine and other severe service industrial environments and is suitable for fresh and salt water immersion resistance. This high solids, high performance epoxy is application friendly and can be used at low temperatures down to 20°F.


  • Carboguard 501

    Features:

    • Solvent free
    • Excellent film strength, abrasion, and impact resistance
    • Rapid hardening for quick service
    • Easy to mix ratios
    • Excellent film build and working properties

    Description:

    Epoxy patching and surfacing compound that exhibits excellent bond strength and chemical resistance to a variety of acids, alkalies, salt solutions and oils. It is used to fill voids and bugholes in precast or poured-in-place concrete and other masonry surfaces. Repairs damaged concrete, fills narrow cracks, and can be used as a coving material for floor-wall transitions or lap joint areas. May also be used to repair weld seams and pits in metal.


  • Carboguard 60

    Features:

    • Low odor and low VOC
    • Available in a variety of rapid tint colors*
    • Attractive medium sheen for tank exteriors
    • Good chemical resistance
    • Used as a primer, intermediate, or finish coat
    • Fast cure & dry times
    • Can be applied over power tool cleaned surfaces
    • VOC compliant to current AIM regulations
    • Good abrasion resistance

    Description:

    Carboguard 60 is a high solids, versatile, abrasion resistant, chemical resistant, and corrosion resistant coating. It can be used as a primer, intermediate coat, or self-priming finish over steel or inorganic zinc primers. May be topcoated with itself, or a broad variety of high performance finish coats. This product has excellent wetting properties giving it the capability of going over marginally prepared substrates. It is ideal for maintenance and fabrication shop applications. An optional Glass Flake (GF) additive or micaceous iron oxide (MiO) additive can be purchased separately and may be used to enhance film strength for more abusive applications for severe marine or heavy industrial uses. Consult Technical Service for suitability as a lining or other exposures.


  • Carboguard 60 Tank White

    Features:

    • Low odor and low VOC
    • Available in self-cleaning white
    • May be used as a primer, intermediate, or finish coat
    • Fast cure & dry times
    • Can be applied over power tool cleaned surfaces
    • VOC compliant to current AIM regulations

    Description:

    Carboguard 60 Tank White is a specially formulated high solids, versatile corrosion resistant coating designed for use as a weathering finish for exterior use. It has the unique ability to freely chalk on UV exposure to maintain a white appearance over its useful life making it ideal for tank exteriors and the like for both new construction or maintenance.


  • Carboguard 61

    Features:

    • Low odor and low VOC
    • Low temperature cure
    • Available in a variety of colors
    • ANSI/NSF Std. 61 for potable water tanks 2000 gallons or larger
    • ANSI/NSF Std. 61 for water pipes 54" inch ID or larger
    • ANSI/NSF Std. 61 for 4" valves or larger
    • AWWA D102 Inside System #1 and #2

    Description:

    Carboguard 61 is a high solids, corrosion resistant coating designed as a potable water lining for tanks and pipes. This product has excellent wetting properties resulting in good adhesion properties.


  • Carboguard 635

    Features:

    • Low temperature cure (20°F)
    • Excellent corrosion protection
    • Excellent application characteristics
    • Fast recoat times
    • Moisture tolerance during application
    • Extended recoat window for atmospheric exposures (6 months for most topcoats)
    • ANSI/NSF Standard 61 for potable water (see UL's website for details)*
    • Complies with IMO Resolution MSC.215(82) for seawater ballast tanks

    Description:

    An all-purpose immersion-grade epoxy that has a variety of attributes including low-temperature cure, surface tolerance, fast recoat times, moisture tolerance during application and cure, and excellent corrosion protection. Can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. Suitable for both maintenance and new construction projects due to its excellent surface wetting characteristics and quick cure for handling. May also be used for immersion in potable water, fresh or salt water (marine) exposures.


  • Carboguard 635 HAR

    Features:

    • Low temperature cure (20°F)
    • Excellent corrosion protection
    • Excellent application characteristics
    • Fast recoat times
    • Moisture tolerance during application
    • Extended recoat window for atmospheric exposures (6 months for most topcoats)
    • Meets VOC restrictions

    Description:

    An all-purpose epoxy that has a variety of attributes including low-temperature cure, surface tolerance, fast recoat times, moisture tolerance during application and cure, and excellent corrosion protection. Carboguard 635 HAR can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. It is suitable for both maintenance and new construction projects due to its excellent surface wetting characteristics and quick cure for handling. It may also be used for immersion in fresh or salt water (marine) exposures. See also marine-version data sheet.


  • Carboguard 635 VOC

    Features:

    • Low temperature cure (20°F)
    • Excellent corrosion protection
    • Excellent application characteristics
    • Fast recoat times
    • Moisture tolerance during application
    • Extended recoat window for atmospheric exposures (6 months for most topcoats)
    • Low VOC and low HAPs content

    Description:

    An all-purpose immersion-grade epoxy that has a variety of attributes including low-temperature cure, surface tolerance, fast recoat times, moisture tolerance during application and cure, and excellent corrosion protection. It has low VOC and low HAP's content for use in areas with restricted volatile emissions. Can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. Suitable for both maintenance and new construction projects due to its excellent surface wetting characteristics and quick cure for handling. May also be used for immersion in potable water, fresh or salt water (marine) exposures.


  • Carboguard 690

    Features:

    • High solids, low VOC
    • High build (16 mils)
    • Low temperature cure (20°F)
    • Excellent moisture tolerance during application
    • Fast cure response
    • Suitable for use in USDA inspected facilities

    Description:

    High performance, surface tolerant epoxy that has excellent resistance to water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. Can be used on structural steel, piping, tankage, and equipment exposed to industrial or marine environments. It can also be used in immersion service for salt water, process water (non-potable) and waste water treatment projects; and is ideal for coatings under insulation on pipes up to 300°F(150°C).


  • Carboguard 690 GF

    Features:

    • High solids, low VOC
    • High build (20+ mils)
    • Low temperature cure (20°F)
    • Excellent moisture tolerance during application
    • Fast cure response
    • Excellent physical and barrier properties

    Description:

    High performance, glass-flake filled, cold cure epoxy having excellent film strength and resistance to water, salt water and wastewater exposures. This coating exhibits outstanding moisture tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. Glass flake reinforcement enhances film strength, impact resistance and barrier properties. Can be used on a variety of surfaces including structural steel, piping, pilings, ships, offshore structures and other equipment exposed to industrial or marine environments. It can also be used in immersion service for salt water, process water (non-potable) and waste water treatment projects.


  • Carboguard 695 CLR

    Features:

    • Solventless, high performance protection
    • Low odor
    • Easy to apply by standard equipment
    • Excellent chemical resistance
    • Fast cure
    • Tough abrasion resistant film
    • Excellent flexibility
    • Excellent corrosion protection
    • Impact resistant
    • High-build application
    • "Long fiber" internal film reinforcement
    • Low temperature cure (35 °F)

    Description:

    Solventless, clear, epoxy lining that can be applied using reinforced glass fibers specifically designed to comply with API RP652 for thick-film tank bottom lining repairs. API RP652 specifically recommends "long fiber" reinforcement which can be achieved using a glass mat or chopped glass. The system is suitable for exposures in water, crude oil, aromatic distillates and unblended gasolines. It can be applied by standard or plural-component airless spray equipment depending on the glass reinforcement used.


  • Carboguard 869 Non-Skid

    Features:

    • Easy mix; non settling; 2-component
    • Constant agitation not required during installation
    • Short sweat-in time; long pot life
    • Unique aggregate package for improved nonslip properties
    • Dry hard overnight
    • Excellent film build properties

    Description:

    Carboguard 869 Non-Skid is a two component, polyamide modified, low VOC, high performance coating for demanding industrial maintenance, marine and architectural applications. It is a tough and durable satin finish perfect for use on steel, galvanized, aluminum and masonry. It has a unique non-skid filler package which requires no agitation during application. In spite of its apparent lower profile aggregate, it has improved non-slip properties over larger aggregate materials, even when wet. It has excellent chemical and abrasion resistance, particularly in marine or other corrosive environments. It is suitable for use on properly prepared concrete & steel surfaces in refineries, offshore platforms, chemical plants, food & beverage plants and pulp & paper mills.


  • Carboguard 890

    Features:

    • Excellent chemical resistance
    • Surface tolerant characteristics
    • Conventional and low-temperature versions
    • Self-priming and primer/finish capabilities
    • Very good abrasion resistance
    • VOC compliant to current AIM regulations
    • Suitable for use in USDA inspected facilities

    Description:

    Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial markets. Self-priming and suitable for application over most existing coatings, and tightly adherent rust. Serves as stand-alone system for a variety of chemical environments and is also designed for various immersion conditions. An optional micaceous iron oxide additive (MIO Filer) can be purchased separately and may be used per the Product Data Sheet to enhance corrosion protection and film strength for more aggressive service such as severe marine or heavy industrial uses.


  • Carboguard 890 GF

    Features:

    • Excellent chemical resistance
    • Surface tolerant characteristics for less severe applications
    • Low-temperature version: 890 LT GF
    • Self-priming and primer/finish capabilities
    • Excellent abrasion resistance & hardness
    • VOC compliant to current AIM regulations
    • Non-skid service with optional fillers

    Description:

    A glass reinforced chemically resistant epoxy coating with wide versatility in all industrial markets. It is self-priming. Glass reinforcement improves internal film strength, hardness, impact, and abrasion resistance. It is often used in severe service (above or below the water line) in marine applications where these resistance qualities are desired.


  • Carboguard 890 LT

    Features:

    • Excellent chemical resistance
    • Surface tolerant characteristics
    • Low-temperature cure formulation
    • Self-priming capability
    • Very good abrasion resistance
    • VOC compliant to current AIM regulations
    • Suitable for use in USDA inspected facilities

    Description:

    Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial markets. Self-priming and suitable for application over most existing coatings, and tightly adherent to rust. Excellent for use as a primer or intermediate coat where low temperature cure is needed. Can be used in a variety of chemical environments. May be used as a self-priming or finish coat on exterior exposure if discoloration can be tolerated.


  • Carboguard 890 VOC

    Features:

    • Excellent chemical resistance
    • Surface tolerant characteristics
    • Self-priming and primer/finish capabilities
    • Very good abrasion resistance
    • VOC compliant to current AIM regulations
    • Suitable for use in USDA inspected facilities

    Description:

    Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial markets. Self-priming and suitable for application over most existing coatings, and tightly adherent to rust. Carboguard 890 VOC serves as stand-alone system for a variety of chemical environments.


  • Carboguard 891 VOC

    Features:

    • NSF/ANSI-61 approved for potable water tanks*
    • Meets the FDA requirements for 21CFR 175.300 for direct food contact
    • Two coats applied per the Product Data Sheet meet the requirements of AWWA C210
    • Ultra High solids; Low VOC and HAPs
    • Handles deionized water up to 150°F (66°C)
    • VOC compliant for South Coast; <100 g/l VOC
    • Good chemical resistance
    • Excellent thermal shock resistance
    • Good abrasion resistance

    Description:

    Ultra high solids epoxy that is designed as a liner for potable water, demineralized water, wastewater and many other services. It is widely used as a tank lining for steel and concrete tanks. Product is self-priming and is normally applied in two coats. Formulated for application at conventional builds (4 to 6 mils per coat) as well as high builds (10 mils per coat).


  • Carboguard 893

    Features:

    • Excellent corrosion protection
    • Excellent film build and edge protection
    • Used as a primer or an intermediate coating
    • Good abrasion resistance
    • Cures down to 40°F
    • VOC compliant to current AIM regulations

    Description:

    High solids corrosion resistant primer and intermediate. Used either as a primer or an intermediate coat over steel and inorganic zinc primers. Can be topcoated with a broad variety of high performance finish coats.


  • Carboguard 893 SG

    Features:

    • Ready to apply after mixing; no sweat-in time or thinning required.
    • Economical fit for use epoxy
    • Available in a variety of rapid tint colors
    • Attractive low sheen for tank exteriors
    • Used as a primer, intermediate, or finish coat
    • Power tool cleaned surfaces acceptable
    • Optional low temperature (LT) cure Part B
    • VOC compliant to current AIM regulations

    Description:

    Versatile corrosion resistant coating. Used either as a primer, intermediate coat, or self-priming finish over steel and zinc primers. May be topcoated with itself, or a broad variety of high performance finish coats. Product also has surface tolerant properties. Optional (LT) cure for 35°F cure capability


  • Carboguard 893 SG LT

    Features:

    • Ready to apply after mixing; no sweat-in time or thinning required.
    • Economical fit for use epoxy
    • Available in a variety of rapid tint colors
    • Attractive low sheen for tank exteriors
    • Used as a primer, intermediate, or finish coat
    • Power tool cleaned surfaces acceptable
    • VOC compliant to current AIM regulations

    Description:

    Versatile corrosion resistant coating. Used either as a primer, intermediate coat, or self-priming finish over steel and zinc primers. May be topcoated with itself, or a broad variety of high performance finish coats. Product also has surface tolerant properties and low temperature 35 °F (2 °C) cure capability.


  • Carboguard 893 SG MIO

    Features:

    • Ready to apply after mixing; no sweat-in time or thinning required.
    • Economical fit for use epoxy
    • Used as a primer or intermediate coat
    • Can be applied over power tool cleaned surfaces
    • Micaceous iron oxide (MiO Filler) for additional barrier properties and corrosion resistance: MiO is purchased separately
    • Optional low temperature (LT) cure Part B
    • VOC compliant to current AIM regulations

    Description:

    Versatile corrosion resistant coating with zinc phosphate corrosion inhibitor. Contains additional filler reinforcement (micaceous iron oxide) for enhanced barrier resistant properties. Used either as a primer or intermediate coat over steel, other epoxies or inorganic zinc primers. May be topcoated with a broad variety of high performance finish coats. Has surface tolerant properties. Has optional (LT) cure for 35°F cure capability.


  • Carboguard 893N

    Features:

    • Excellent corrosion protection
    • Excellent film build and edge protection
    • Used as a primer or an intermediate coating
    • Good abrasion resistance
    • VOC compliant to current AIM regulations
    • Tested for Nuclear Service Level 1

    Description:

    Nuclear grade, DBA tested, self priming epoxy. Tested and certified for use in Nuclear Level 1 areas in a variety of systems.


  • Carboguard 894

    Features:

    • Immersion- grade epoxy
    • High solids, low VOC
    • Excellent adhesion
    • Excellent flexibility
    • Long recoat window

    Description:

    Carboguard 894 is a high performance, versatile, immersion-grade, VOC compliant, high build, self-priming epoxy. It is suitable for industrial and marine environments in fresh or salt water immersion. It can also be used for tank exteriors, structural steel, piping, or process equipment. Carboguard 894 may be used on barges, vessels and other marine applications where a high quality epoxy is needed.


  • Carboguard 896

    Features:

    • Dry bulk service for hopper cars carrying EVA, PTA, PTA, polyethylene (PE), polypropylene (PP), polystrene (PS), polyvinyl chloride (PVC) plastic pellets, and other commodities, which may contain residual process acid. Also complies with 21CFR175.300(b)(3)(viii)(a).

    Description:

    Carboguard 896 is a two component, high solids, modified epoxy formulated for use as a protective hopper lining with excellent resistance to fugitive acetic and hydrochloric acids often found in many plastic pellet cargoes.


  • Carboguard 954 HB

    Features:

    • Surface tolerant characteristics to existing finishes and SP2, SP3-cleaned steel
    • Single-coat application in most instances
    • High-build capability
    • Self-priming and primer/finish capabilities
    • Excellent abrasion and moisture resistance
    • True brush & roll characteristics
    • VOC compliant to current AIM regulations

    Description:

    All-purpose, high-build, solvent-free, spray, brush or roll epoxy mastic coating with applications in all industrial markets and for almost all substrates. Product has excellent wetting properties making it ideal for direct-to-substrate (steel or concrete) surface-tolerant applications.


  • Carbomastic 15

    Features:

    • Excellent performance over minimal surface preparation of steel substrates
    • Suitable as a topcoat for most tightly adhered existing coatings
    • Excellent choice for field touch-up of zinc-rich primers and galvanized steel
    • Unique formulation with aluminum flakes provides exceptional barrier protection
    • Available in a low temperature cure version (Carbomastic 15 FC)
    • Suitable for use under insulation on hot surfaces operating up to 300 °F (150 °C)
    • VOC compliant to current AIM regulations

    Description:

    Aluminum-pigmented, low-stress, high-solids mastic with a proven field history. Carbomastic 15 was the pioneer mastic coating in a number of industrial markets and today still provides unmatched levels of barrier protection and corrosion resistance over existing finishes and rusted or SSPC-SP2 or SP3-cleaned steel.


  • Carbomastic 15 FC

    Features:

    • Excellent performance over minimal surface preparation of steel substrates
    • Suitable as a topcoat for most tightly adhered existing coatings
    • Excellent choice for field touch-up of zinc-rich primers and galvanized steel
    • Unique formulation with aluminum flakes provides exceptional barrier protection
    • May be applied at 35°F (2°C) when CM 15 FC's part B is utilized
    • Suitable for use under insulation on hot surfaces operating up to 300°F(150°C)
    • VOC compliant to current AIM regulations

    Description:

    Aluminum-pigmented, low-stress, high-solids mastic with outstanding performance properties and proven field history. Carbomastic 15 was the pioneer mastic coating in a number of industrial markets and today still provides unmatched levels of barrier protection and corrosion resistance over existing finishes and rusted or SSPC-SP2 or SP3-cleaned steel.


  • Carbomastic 18 BT

    Features:

    • Excellent immersion performance in both fresh and sea water
    • Suitable as a rust preventive coating in ballast tanks and hull applications
    • Ideal for sub-sea installations, jackets and other areas exposed to sea water
    • Can be applied as low as 5°C (40°F)
    • Good flexibility
    • Very good abrasion resistance
    • VOC compliant

    Description:

    Carbomastic 18 BT is a fast-curing, heavy-duty, high-build anti-corrosive coating with a broad and versatile list of uses in marine and other corrosive environments. It is an excellent choice for the protection of ship hull exteriors, underwater and ballast tanks. Offshore applications include sub-sea, jackets, production decks, drilling rig legs, pontoons, in immersed surfaces. It meets the demands in IMO Performance Standard for Protective Coatings. It is classified “B1” (Superior Grade) under DNV standard “Testing and Classification of Ballast Tank Coatings”.


  • Carbomastic 615

    Features:

    • High solids, low VOC
    • Low temperature cure
    • Excellent wetting properties
    • Excellent surface tolerance
    • Excellent moisture tolerance (application)
    • Fast cure response
    • Suitable for immersion service in fresh or salt water after 60 minute cure @75°F

    Description:

    High performance epoxy that has excellent resistance to fresh and salt water exposures. This coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. It contains an inert flake reinforcement (micaceous iron oxide) to enhance film strength and performance. This product is ideal for industrial or heavy duty marine environments for the protection of steel against salt laden environments.


  • Carbomastic 615 AL

    Features:

    • Unique formulation with aluminum flakes provides exceptional barrier protection
    • High solids, low VOC
    • Low temperature cure
    • Excellent wetting properties
    • Excellent surface tolerance
    • Excellent moisture tolerance during application
    • Fast cure response
    • Suitable for immersion service in fresh or salt water after 60 minute cure @75°F

    Description:

    High performance, aluminum-filled epoxy that has excellent resistance to fresh and salt water exposures. This coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service. This aluminum-pigmented epoxy also contains inert flake reinforcement (micaceous iron oxide) to enhance film strength and performance.


  • Carbomastic 90

    Features:

    • Very good performance over minimal surface preparation of steel substrates
    • Suitable as a tie-coat/topcoat for most tightly adhered existing coatings
    • Excellent film build on edges
    • Can be applied at temperatures as low as 40°F
    • VOC compliant to current AIM regulations

    Description:

    Economical, aluminum-pigmented mastic with excellent performance properties. Designed for a broad range of applications, this material provides good corrosion resistance, film build and surface tolerance. Can be applied at low temperatures and cures faster than many other epoxy mastics.


  • Carbomastic 94

    Features:

    • Surface tolerant epoxy mastic
    • Excellent corrosion protection
    • Low VOC
    • Custom colors available via RTS
    • Excellent wetting properties and adhesion
    • High solids, low stress over existing coatings
    • High film build, up to 7 mils DFT per coat
    • Class A Flame Spread and Smoke Development
    • Excellent durability
    • Good flexibility and impact resistance
    • Outstanding abrasion resistance
    • Good chemical resistance
    • Long pot life
    • Long maximum re-coat, up to 1 year
    • Approved topcoat over many Carboline Fireproofing Materials

    Description:

    A high performance, surface tolerant, high build, corrosion resistant epoxy mastic. It has outstanding adhesion to metal substrates along with most aged coatings and offers maximum protection against severe weather conditions, corrosion, moisture penetration and general industrial environments. It wets and penetrates firm rust and tight crevices and resists further rust deterioration. Use it on tank exteriors, structural steel, piping, process equipment, bridges & water towers. Carbomastic 94 may also be used on barges, vessels and other marine applications. An optional micaceous iron oxide, (MIO), additive can be purchased separately and may be used per its Product Data Sheet to further enhance the coatings's performance.


  • Carbothane 133 FC

    Features:

    • Outstanding performance properties in both mild and aggressive environments
    • Fast cure
    • High build; suitable for many two-coat systems
    • Suitable for application direct to inorganic zincs
    • Application by spray, brush or roller
    • Indefinite recoatability
    • VOC compliant to current AIM regulations
    • Contains no reportable HAP's

    Description:

    High build, low sheen finish that has excellent resistance to corrosion, chemicals and abrasion. Suitable for application over a number of Carboline primers and intermediates, this material provides very good weathering performance in a broad range of colors.


  • Carbothane 133 HB

    Features:

    • Outstanding performance properties in both mild and aggressive environments
    • High build; suitable for many two-coat systems
    • Suitable for application direct to inorganic zincs
    • Application by spray, brush or roller
    • Indefinite recoatability
    • VOC compliant to current AIM regulations

    Description:

    High build, low sheen finish that has excellent resistance to corrosion, chemicals and abrasion. Suitable for application over a number of Carboline primers and intermediates, this material provides very good weathering performance in a broad range of colors.


  • Carbothane 133 VOC

    Features:

    • Compliant to AWWA D102-11, OCS-4 & OCS-6
    • Outstanding performance properties in virtually all industrial markets
    • High build; suitable for many two-coat systems
    • High solids formulation allows for improved edge protection
    • Suitable for application direct to inorganic and organic zinc primers
    • Indefinite recoatability
    • VOC compliant to current AIM regulations
    • Suitable for use in USDA inspected facilities

    Description:

    High solids, high build, satin finish that provides a tough attractive finish while exhibiting outstanding performance properties. Demonstrates extremely good resistance to abrasion, corrosion and chemical exposure when applied over recommended Carboline primers and/or intermediate coats.


  • Carbothane 134 GS

    Features:

    • Very good weathering (75% gloss retention after 4000 hours QUV-A exposure)
    • Exceeds SSPC-Paint Spec 36; Level 3
    • 6 hours dry to handle time
    • High gloss appearance
    • Brush, roll, or spray application
    • Indefinite recoatability
    • Minimum 2 hours working time

    Description:

    Carbothane 134 GS is an excellent weatherable finish for exterior exposures in industrial and marine environments. It has wide versatility as a high gloss aesthetically pleasing finish for a variety of exposures. It is an ideal topcoat over epoxy primers or intermediates to enhance appearance and longer term weathering characteristics.


  • Carbothane 134 HG

    Features:

    • High solids, low VOC content
    • Excellent weatherability
    • Exceeds SSPC Paint 36 specification for a Level 3 urethane
    • Available in all Carboline colors including metallic-pigmented colors
    • Excellent flow characteristics allow for application by spray or roller
    • Superior impact and abrasion resistance
    • Indefinite recoatability
    • VOC compliant to current AIM regulations
    • Suitable for use in USDA inspected facilities

    Description:

    Thin film, high gloss finish with exceptional weathering performance characteristics. Used extensively in virtually all industrial markets, 134 HG provides a smooth, durable finish that has superior resistance to corrosion, abrasion and chemical exposure.


  • Carbothane 134 HG Aluminum

    Features:

    • High solids, low VOC content
    • Excellent weatherability
    • Available in metallic-pigmented colors
    • Excellent flow characteristics allow for application by spray or roller
    • Superior impact and abrasion resistance
    • Indefinite recoatability
    • VOC compliant to current AIM regulations

    Description:

    Thin film, high gloss finish with exceptional weathering performance characteristics. Used extensively in virtually all industrial markets, 134 HG provides a smooth, durable finish that has superior resistance to corrosion, abrasion and chemical exposure.


  • Carbothane 134 HS

    Features:

    • Excellent weatherability
    • Excellent flexibility
    • Excellent abrasion resistance
    • Available in Carboline’s Rapid Tint System
    • Meets most VOC requirements
    • Indefinite recoatability

    Description:

    An attractive, high gloss, high solids topcoat which is easily applied by airless or conventional spray to yield a smooth, easily cleanable surface. Recommended use as a finish coat for the exteriors of tanks, equipment, piping, structural steel, and concrete surfaces where chemical resistance, toughness, and weatherability are required. An excellent coating for use in chemical processing, pulp and paper, petro-chemical, bridge, offshore, railcars, heavy marine, institutional and waste treatment facilities where a highly resistant and attractive coating is desired. Not recommended for immersion service.


  • Carbothane 134 RS

    Features:

    • Very good weathering (75% gloss retention after 4000 hours QUV-A exposure)
    • Exceeds SSPC-Paint Spec 36; Level 3
    • 6 hours dry to handle time
    • High gloss appearance
    • Brush, roll, or spray application
    • Minimum 2 hours working time

    Description:

    Carbothane 134 RS is an excellent weatherable finish for exterior exposures in industrial and marine environments. It has wide versatility as a high gloss aesthetically pleasing finish for a variety of exposures. It is an ideal topcoat over epoxy primers or intermediates to enhance appearance and longer term weathering characteristics.


  • Carbothane 134 VOC

    Features:

    • High solids, low VOC content
    • Excellent weatherability
    • Exceeds SSPC Paint 36 specification for a Level 3 urethane
    • Excellent flow characteristics allow for application by spray or roller
    • Superior impact and abrasion resistance
    • Indefinite recoatability
    • VOC compliant to current AIM regulations
    • Suitable for use in USDA inspected facilities

    Description:

    High gloss finish with exceptional weathering performance characteristics. Used extensively in virtually all industrial markets, provides a smooth, durable finish that has superior resistance to corrosion and chemical exposure.


  • Carbothane 134 WB

    Features:

    • Water based, low VOC content
    • Excellent weatherability
    • Exceeds SSPC Paint 36 specification for a Level 3 urethane
    • Suitable for USDA inspected facilities
    • Available in most Carboline and custom colors
    • Excellent flow characteristics allow for application by spray or roller
    • Flexible, impact and abrasion resistant film
    • Indefinite recoatability
    • VOC compliant to current AIM regulations

    Description:

    Thin film, high gloss finish with exceptional weathering performance characteristics. Used for the weathering protection of a variety of substrates in all architectural and industrial markets. It provides a smooth, durable finish that has excellent weathering resistance, gloss and color retention..


  • Carbotherm 3300

    Features:

    • Excellent thin-film insulation
    • Unique formula provides superior coverage during application
    • Protects personnel from hot surfaces
    • Multi-purpose interior/exterior coating
    • Insulation provides anti-condensation properties
    • Easy to use
    • Zero VOC; Low odor
    • May be applied to hot surfaces

    Description:

    Carbotherm 3300 is a ceramic blend insulative composite coating formulated in a high temperature resistant acrylic binder. It is ideally suited as a protective heat barrier to shield personnel from hot surfaces. It also inhibits heat transfer into or out of a structure. Its insulative properties keeps structures exposed to solar radiation significantly cooler. It can be used to minimize or eliminate sweating of pipes or other operating equipment.


  • Carbotherm 551

    Features:

    • Excellent thin-film insulation
    • Unique epoxy formula outperforms acrylic-based materials
    • Tougher and more durable than acrylic coatings
    • Higher chemical resistance than acrylic coatings
    • Topcoats are optional
    • Protects personnel from hot surfaces
    • Ideal for industrial/aggressive applications
    • Insulation provides anti-condensation properties
    • Acceptable for use in USDA facilities
    • High film build per coat; fewer coats
    • Low VOC; low odor
    • May be applied to hot surfaces

    Description:

    Carbotherm 551 is a unique insulative composite coating formulated in a high temperature resistant epoxy binder. Unlike acrylic-based insulative materials it has superior toughness, hardness, impact resistance, chemical resistance and permeation resistance. It is therefore more suitable for industrial applications or other physically demanding environments. It is an ideal protective heat barrier to shield personnel from hot surfaces. It also inhibits heat transfer into or out of a structure. Its insulative properties keeps structures exposed to solar radiation significantly cooler. It can be used to minimize or eliminate condensation of pipes or other operating equipment. Its superior application properties of higher film build per coat and fewer coats offers savings and quicker return to service. Because it bonds directly to the surface (unlike standard insulation materials) it minimizes water entry and the effect of corrosion under insulation.


  • Carboweld 11

    Features:

    • Welds made over Carboweld 11 coated steel are equal in every respect to welds made to uncoated steel
    • Designed to protect steel during construction phase of projects under normal conditions
    • Can be topcoated for additional long term protection for atmospheric exposures.
    • Weld spatter does not adhere to or damage the coating
    • Can be welded as quickly and easily as bare steel at production line speeds without loss in strength or consistency of the weld
    • Dries to touch and to handle in 3 to 5 minutes
    • Certified as a pre-construction primer for Lloyds Register constructions

    Description:

    A weldable pre-construction inorganic zinc primer for shop use only.


  • Carboweld 11 WB

    Features:

    • Excellent corrosion protection
    • High zinc loading per square foot
    • Zero VOC
    • Good resistance to salting
    • Fast curing, quick handling
    • Excellent application characteristics (less likely to pump packing or tip plug)

    Description:

    Carboweld 11 WB is a water-based inorganic zinc rich primer that protects steel galvanically, eliminating subfilm corrosion. It meets VOC regulations while providing the proven performance of silicate zinc rich technology. It may be used as a weldable pre-construction primer or as a primer under many different types of topcoats.


  • Carboweld 9 WB

    Features:

    • High zinc content
    • Zero VOC, water based formula
    • Cathodic protection
    • Excellent undercutting resistance
    • Weldable pre-construction primer
    • Certified for potable water use under ANSI/NSF
    • Standard 61 by Underwriters Laboratories (see Limitations)

    Description:

    Carboweld 9 WB is a fast drying, high zinc content, 2-package pre-construction primer for steel substrates. It performs well as a shop/yard primer for corrosion protection during fabrication phase. It provides cathodic sacrificial protection and thus prevents corrosion of the underlying steel, like galvanizing. It contains 81% zinc dust by weight in the dried film. This waterborne product has no VOC or flash point. It can be used as a shop primer when weldability and corrosion protection are necessary. Use it in industrial, marine & process environments.


  • Carbowrap Mastic

    Features:

    • Contain no VOC's
    • Resists harsh chemical exposures
    • Will not crack or harden over time
    • Application in any weather
    • Provides an impermeable protective layer
    • No special tools required for application
    • Complies with AWWA C217 specification
    • Provides excellent protection against chemical splash or fume attack
    • Tensile Strength: 45 lbs/inch
    • Water Vapor Permeability: 0.12 g/m2 per 24 hours

    Description:

    Carbowrap Mastic is afiller which profiles areas to be wrapped by easing contours on pipe joints, flanges, valves, bolts, and other irregular shapes. Consists of saturated petroleum based compounds, inert fillers, and reinforcing fibers. Carbowrap Mastic is part of the Carbowrap system developed for the protection of metal surfaces in severe environments and difficult to protect applications. The Carbowrap System is designed to be applied over hand or power wire brushed surfaces for above ground, buried, and underwater applications. The typical system involves priming the surface with a paste (Carbowarp Paste), profiling around irregular shapes with a mastic compound (Carbowrap Mastic), and wrapping with a petroleum tape (Carbowrap Tape A, B, C or Marine Tape). An optional overwrap tape (Carbowrap Overwrap) is used for additional mechanical or electrical resistance.


  • Carbowrap Tape A

    Features:

    • Contain no VOC's
    • Resists harsh chemical exposures
    • Will not crack or harden over time
    • Application in any weather
    • Provides an impermeable protective layer
    • No special tools required for application
    • Complies with AWWA C217 specification
    • Provides excellent protection against chemical splash or fume attack
    • Tensile Strength: 45 lbs/inch
    • Water Vapor Permeability: 0.12 g/m2 per 24 hours
    • Service Temperature: 131 °F (55 °C)

    Description:

    Carbowrap Tape is a non-woven bonded synthetic fabric, fully impregnated and coated with natural petroleum based compounds and inert fillers. It is chemically inert, does not polymerize or oxidize, and retains water resistance and dielectric properties over an indefinite period. Three different tapes are available depending on the service temperatures (130 °F [54 °C], 150 °F [66 °C], and 165 °F [74 °C] respectively). Carbowrap Tape is part of the Carbowrap system developed for the protection of metal surfaces in severe environments and difficult to protect applications. The Carbowrap System is designed to be applied over hand or power wire brushed surfaces for above ground, buried, and underwater applications. The typical system involves priming the surface with a paste (Carbowarp Paste), profiling around irregular shapes with a mastic compound (Carbowrap Mastic), and wrapping with a petroleum tape (Carbowrap Tape A, B, C or Marine Tape). An optional overwrap tape (Carbowrap Overwrap) is used for additional mechanical or electrical resistance.


  • Carboxane 2000

    Features:

    • Exceptional weatherability
    • Long life performance
    • Outstanding gloss/color retention
    • VOC compliant
    • Excellent abrasion resistance
    • Isocyanate free
    • Flexible Film

    Description:

    Carboxane 2000 is a premium, ultra-durable coating that provides outstanding gloss and color retention for exterior exposures. When used over a suitable primer (as a two coat system) Carboxane 2000 provides the barrier properties normally seen using a three-coat system (primer, epoxy intermediate with an acrylic-polyurethane finish) for most environments. This tightly cross-linked film utilizes a UV-resistant siloxane binder resulting in a finish with outstanding barrier properties and weathering performance that far exceeds polyurethanes.


  • Carboxane 2000 Satin

    Features:

    • Exceptional weatherability
    • Long life performance
    • Outstanding gloss/color retention
    • High build
    • VOC compliant
    • Excellent abrasion resistance
    • Isocyanate free
    • Flexible Film
    • Class A Flame Spread (ASTM E84)

    Description:

    Carboxane 2000 Satin is a premium, ultra-durable coating that provides outstanding gloss and color retention for exterior exposures. Carboxane 2000 Satin combines the chemical resistant properties of epoxies with the weathering characteristics of top-end, acrylic-polyurethanes that can replace three-coat systems with two-coats, by eliminating the intermediate coat of epoxy. This tightly cross-linked film results in a finish with outstanding barrier properties and weathering performance that far exceeds polyurethanes. The satin gloss maintains its appearance and is chalk-free for the duration of its expected service life.


  • Carboxane 950 Clear Gloss

    Features:

    • Ambient temperature cure; no heat cure required
    • Meets AAMA 605.2 requirements (industry standard for PVDF finishes)
    • Exceptional weatherability
    • Excellent flow characteristics allow for application by spray or roller
    • Excellent graffiti resistance
    • Enhances long term performance over pigmented or metallic finishes

    Description:

    Premium, ultra-durable ambient cured clear coat finish meeting AAMA 605.2 performance requirements. This high gloss coating provides unparalleled color and gloss retention and exterior weathering characteristics. It offers a level of durability for field application previously not available in the construction industry. Also can be applied directly to aged PVDF finishes.


  • Carbozinc 11

    Features:

    • Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces.
    • Rapid cure. Dry to handle in 45 minutes at 60°F (16°C) and 50% relative humidity.
    • Low temperature cure down to 0°F (-18°C).
    • High zinc loading.
    • Meets FDA requirements.
    • Zinc supplied meets ASTM D520 (Type II)*
    • Meets SSPC Paint 20 Type I, Level 1 for zinc content.
    • Very good resistance to salting.
    • May be applied with standard airless or conventional spray equipment.
    • VOC compliant in certain areas

    Description:

    Time-tested corrosion resistant primer that protects steel galvanically in the harshest environments. For over five decades, Carbozinc 11 (CZ 11) has been the industry standard for high-performance inorganic zinc protection on steel structures worldwide.


  • Carbozinc 11 FC

    Features:

    • Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces.
    • Rapid cure.Dry to handle in 30 minutes at 75°F (24°C) and 60% RH
    • Can be topcoated in 4-5 hours at 75°F/24°C and minimum 60% RH
    • High zinc loading
    • Tolerant to mudcracking (up to 6 mils/150 microns)
    • Smooth uniform texture reduces topcoat bubbling
    • Meets FDA requirements in gray color
    • Very good resistance to salting
    • May be applied with standard airless or conventional spray equipment
    • Low HAPs content of 0.12 lbs/solid gallon

    Description:

    Time-tested corrosion resistant technology that protects steel galvanically in the harshest environments. For over five decades, Carbozinc 11 Series primers have been the industry standard for high-performance inorganic zinc protection on steel structures worldwide. Carbozinc 11 FC is a faster-cure formulation that allows fast topcoating times making it ideal for quick turn around projects.


  • Carbozinc 11 HS

    Features:

    • Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces
    • Rapid cure. Dry to handle in 1 hour at 75°F (24°C) and 50% relative humidity
    • Low temperature cure down to 15°F (-9°C)
    • High zinc loading
    • Very good resistance to salting
    • May be applied with airless or conventional spray
    • Excellent as a lining for solvent storage* (Green color only)
    • May be used as a weldable pre-construction primer
    • Exhibits long-term corrosion resistance
    • Ultra-low VOC level for solvent-based inorganic zincs

    Description:

    Ultra-low VOC member of the Carbozinc family with extraordinary corrosion resistance properties. Carbozinc 11 HS combines unparalleled performance characteristics with an ultra-low VOC formulation that meets some of the most stringent VOC restrictions.


  • Carbozinc 11 SG

    Features:

    • Excellent corrosion and weathering protection.
    • High zinc loading per square foot.
    • Meets Class “B” slip co-efficient and creep testing criteria for use on faying surfaces.
    • Very good resistance to salting.
    • Meets nuclear requirements for level one areas.
    • Available in Type III (ASTM D520) zinc dust.

    Description:

    An inorganic zinc rich primer that protects steel galvanically, eliminating sub-film corrosion.


  • Carbozinc 11 VOC

    Features:

    • Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces
    • Rapid cure. Dry to handle in 1 hour at 75°F (24°C) and 50% relative humidity
    • High zinc loading
    • Available in ASTM D520, Type II zinc version
    • Very good resistance to salting
    • May be applied with standard airless or conventional spray equipment
    • VOC compliant to current AIM regulations

    Description:

    Low VOC version of the original Carbozinc 11 primer, which protects steel galvanically. Carbozinc 11 VOC provides excellent performance properties with a low VOC value of 389 g/l (as supplied).


  • Carbozinc 11 WB

    Features:

    • Excellent corrosion protection
    • High zinc loading per square foot
    • Zero VOC
    • Good resistance to salting
    • Fast curing, quick handling
    • Weldable version available Carboweld 11 WB
    • Excellent application characteristics (less likely to pump packing or tip plug)
    • Meets Class B slip coefficient and creep testing criteria for use on faying surfaces.

    Description:

    Carbozinc 11 WB is a water-based inorganic zinc rich primer that protects steel galvanically, eliminating subfilm corrosion. It meets VOC regulations while providing the proven performance of silicate zinc rich technology. It may be used as a primer under many different types of topcoats.


  • Carbozinc 18 WB

    Features:

    • Outstanding corrosion protection
    • Zero VOC
    • Outstanding undercutting resistance
    • High zinc content
    • Permanent protection

    Description:

    Carbozinc 18 WB is a fast drying, high zinc content, coating for steel substrates. It has outstanding performance in demanding corrosive environments. It self heals to continue protection when damaged. It provides cathodic sacrificial protection and thus prevents corrosion of the underlying steel, like galvanizing. It contains 90% zinc dust by weight in the dried film. This waterborne product has no VOC or flash point. It is comparable to federal specification DOD-P24648 and meets Class B requirements for Slip Coefficient and Creep Resistance, 0.69. Use in industrial, marine, and process environments.


  • Carbozinc 858 (3K)

    Features:

    • Protects steel galvanically
    • Outstanding application properties
    • Cures at low temperatures down to 35°F(2ºC)
    • Tough and abrasion resistant film
    • Wide use in severe industrial or marine environments

    Description:

    A high-solids, zinc-filled epoxy primer for corrosion protection of structural steel in highly corrosive environments including offshore, marine and industrial. This low VOC, HAPs compliant primer has quick cure-to-topcoat characteristics for in-shop applications and quick turnaround capabilities for the field. It has excellent adhesion and undercutting resistance and is outstanding for use as a corrosion resistant primer for a variety of applications.


  • Carbozinc 859

    Features:

    • Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces
    • Rapid cure. Dry to recoat in 30 minutes at 75°F (24°C) and 50% relative humidity.
    • Complies with SSPC Paint 20 (Type II)
    • Low temperature cure down to 35°F (2°C)
    • Excellent adhesion
    • Protects against undercutting corrosion
    • Field proven primer that applies well by spray methods
    • Excellent touch-up primer by brush or roll for small areas.
    • VOC compliant to current AIM regulations

    Description:

    Low VOC organic zinc epoxy steel primer with extremely fast cure-to-topcoat characteristics for in-shop applications and quick turnaround requirements in the field. Carbozinc 859 has less than 3.0 lbs/gallon VOC (thinned) and is used extensively in virtually all industrial markets.


  • Carbozinc 859 VOC

    Features:

    • Rapid cure. Dry to recoat in 30 minutes at 75°F (24°C) and 50% relative humidity.
    • Complies with SSPC Paint 20 (Type II)
    • Meets Class B slip co-efficient and creep testing criteria for use on faying surfaces up to 3 mils dry (See "Dry Film Thickness" section)
    • Low temperature cure down to 35°F (2°C)
    • Excellent adhesion
    • Protects against undercutting corrosion
    • Available in ASTM D520, Type II zinc version
    • Field proven primer that applies well by spray methods
    • Excellent touch-up primer by brush or roll for small areas.
    • Extremely low VOC (less than 100 g/l)
    • Low HAPS (0.51 lbs/solid gal)

    Description:

    Ultra-low VOC organic zinc epoxy steel primer with extremely fast cure-to-topcoat characteristics for in-shop applications and quick turnaround requirements in the field. Carbozinc 859 VOC has less than 100 g/l VOC (thinned) and can be used in virtually all industrial markets.


  • Carbozinc 8701

    Features:

    • Excellent application properties
    • Tough abrasion resistant film
    • Excellent adhesion & undercutting resistance
    • Superior corrosion resistance
    • Meets VOC (Volatile Organic Content) regulations
    • Fast drying for quick recoating

    Description:

    A two-component, high solids, zinc rich epoxy primer formulated for the protection of properly prepared steel substrates. This product can be applied by conventional or airless spray. Recommended for Original Equipment Manufacturers where a high performance, highly corrosion resistant zinc primer is desired. Typical applications include marine, offshore drilling equipment, truck trailer chassis, underbodies and related equipment, industrial and off-road machinery, electrical transformers, industrial tanks, vessels, pumps and processing equipment.


  • Firefilm A5

    Features:

    • Very low VOC
    • Designed for on-site use
    • Meets BS476 Part 21: 1987 Certification
    • Meets C1 and C2 Environments Building Classification (ISO 12944)

    Description:

    Firefilm A5 is a water-based, white, thin film intumescent coating for the protection of internal structural steelwork. It is designed to provide up to 60 minutes of fire resistance. The recommended use for this product is fireproofing of interior steel beams, columns, tubes, and pipes.


  • Firefilm FC2

    Features:

    • Fast cure
    • Low VOC
    • No solvent entrapment or prolonged solvent odour
    • High build potential (1.0 mm / 39.4 mils per coat)
    • Full thickness achievable in 1 coat
    • Designed for on-site and off-site use
    • Meets BS476 Part 2: 1987 Certification
    • Meets EN13381: Part 8 Certification
    • Meets C1, C2 and C3 Environments Building Classification (ISO 12944)

    Description:

    Firefilm FC2 is a low VOC, one coat, high build system, based on patented technology. It provides a fast cure effective structural fire performance, for steelwork, with up to a 120 minute fire rating.


  • Firefilm<sup>®</sup> A4

    Features:

    • Very low VOC
    • Designed for on-site use
    • Meets BS476 Part 21: 1987 Certification
    • Meets C1 and C2 Environments Building Classification (ISO 12944)

    Description:

    Firefilm A4 is a water-based, white, thin film intumescent coating designed for the fire protection of internal structural steelwork for up to a 120 minutes fire resistance. The recommended use for this product is fireproofing of interior steel beams, columns, tubes, and pipes.


  • FP-Fiberglass Mesh 4'x150'

    Features:

    Description:

    FP-Fiberglass Mesh is a high strength fiberglass reinforcing mesh designed for use with Thermo-Lag® intumescent fireproofing products.


  • Galoseal WB

    Features:

    • Single component
    • Low odor, low VOC
    • Contains no heavy metals or mineral acids
    • Extended recoat time
    • Accepts two-component finishes
    • Fast dry

    Description:

    Water-based acrylic primer used to promote adhesion over galvanizing and other nonferrous metal substrates. Unique formula has very low VOC and accepts two-component, solvent containing finishes like epoxies and urethanes.


  • High Temp Mesh

    Features:

    Description:

    High Temp Mesh is an open leno weave, 99+% carbon content, high temperature mesh used as a reinforcing media with Thermo-Lag®, Pyroclad® and Thermo-Sorb® intumescent fireproofing products. The mesh is supplied with a coated finish to enhance handling.


  • Phenoline 1205

    Features:

    • Excellent resistance to acids, caustics, ethanol, gasoline, jet fuels and solvents.
    • Excellent abrasion resistance.
    • Excellent thermal shock resistance (0 to 300° F).
    • VOC compliant to current AIM regulations.
    • Excellent resistance to deionized or demineralized water up to 203°F (95°C).
    • Excellent resistance to crude oil up to 250°F (121°C).
    • Excellent for crude oil storage and transportation up to 250° F (121° C)

    Description:

    Glass flake-filled coating with dense cross-linking that exhibits excellent overall chemical resistance to a variety of aggressive chemicals. Glass reinforcement provides added abrasion resistance, permeation resistance and internal reinforcement. 1205 exhibits very good acid resistance. Excellent for use as a lining for tanks or pipes in process facilities where hot water or abrasive conditions exist.


  • Phenoline 187 UHS Finish

    Features:

    • Excellent solvent/fuel resistance
    • Excellent water resistance
    • High solids, low odor, low VOC
    • Airless spray
    • Conforms to MIL-PRF-23236B(SH) Type IV, Class 2, Grade B
    • For Low Temperature applications 40°F (4.5°C) refer to Phenoline 187 UHS LT Finish

    Description:

    Phenoline 187 UHS Finish is an ultra high solids amine modified epoxy specially formulated to line ballast, oil and fuel storage tanks as well as water tanks and pipes, containment areas and water and waste water treatment plants. It is low in both odor and VOC. It provides excellent surface wetting and adhesion properties.


  • Phenoline 187 UHS LT Finish

    Features:

    • Excellent solvent/fuel resistance
    • Excellent water resistance
    • High solids, low odor, low VOC
    • Airless spray
    • Conforms to MIL-PRF-23236B(SH) Type IV, Class 2, Grade B
    • Low Temperature application and cure 40°F (4.4°C)

    Description:

    Phenoline 187 UHS LT Finish is an ultra high solids low temperature cure amine modified epoxy specially formulated to line ballast, oil and fuel storage tanks as well as water tanks and pipes, containment areas and water and waste water treatment plants. It is low in both odor and VOC. It provides excellent surface wetting and adhesion properties.


  • Phenoline 187 UHS LT Primer

    Features:

    • Excellent solvent/fuel resistance
    • Excellent water resistance
    • High solids, low odor, low VOC
    • Conforms to MIL-PRF-23236B(SH) Type IV, Class 2, Grade B
    • High flash point >200°F (93°C)
    • Low Temperature application and cure 40°F (4.4°C)

    Description:

    Phenoline 187 UHS LT Primer is an ultra high solids low temperature cure amine modified epoxy specially formulated for application under Phenoline 187 UHS LT Finish. It is low in both odor and VOC. It conforms to MIL-PRF-23236B(SH) Type IV, Class 2, Grade B and is recommended for industrial and marine exposures on steel and concrete. It provides excellent surface wetting and adhesion properties. It is used to line ballast, oil, and fuel storage tanks as well as water tanks and pipes, containment areas and water and waste water treatment plants.


  • Phenoline 187 UHS Primer

    Features:

    • Excellent solvent/fuel resistance
    • Excellent water resistance
    • High solids, low odor, low VOC
    • Conforms to MIL-PRF-23236B(SH) Type IV, Class 2, Grade B
    • High flash point >200°F (93°C)
    • For Low Temperature applications 40°F (4.5°C) refer to Phenoline 187 UHS LT Primer

    Description:

    Phenoline 187 UHS Primer is an ultra high solids amine modified epoxy specially formulated for application under Phenoline 187 UHS Finish. It is low in both odor and VOC. It conforms to MIL-PRF-23236B(SH) Type IV, Class 2, Grade B and is recommended for industrial and marine exposures on steel and concrete. It provides excellent surface wetting and adhesion properties. It is used to line ballast, oil, and fuel storage tanks as well as water tanks and pipes, containment areas and water and waste water treatment plants.


  • Phenoline 187 VOC

    Features:

    • High solids; Low VOC formula
    • VOC compliant to current AIM regulations
    • Excellent overall chemical resistance
    • Excellent for crude-oil storage
    • Excellent resistance up to 400°F(204°C)
    • Excellent abrasion & thermal shock resistance
    • Meets the FDA requirements for 21CFR 175.300 for direct food contact.

    Description:

    High solids epoxy lining with exceptional chemical resistance. Primarily as a tank lining, it is recommended for storage of crude oil (180°F/82°C), demineralized water (150°F/65°C), tap water (200°F/93°C) food and beverage industries, and water and wastewater exposures. Is excellent as a protective coating under insulation, operating at (400°F/204°C). Outstanding resistance to wet/dry cycling conditions at these elevated temperatures.


  • Phenoline 309

    Features:

    • Single coat application reduces labor costs
    • Ultra-high build capabilities provides a void-free film and excellent edge protection
    • Wide chemical resistance to acids, caustics and aliphatic solvents
    • Can be mat reinforced where exposure conditions dictate
    • Application by airless spray equipment (plural component acceptable but not required)
    • VOC compliant to current AIM regulations

    Description:

    Single-coat, airless-applied, ultra-high build coating for use on steel and concrete substrates subject to aggressive chemical fume and spill exposure. Phenoline 309 provides exceptional resistance to thermal shock and abrasion, and has found wide acceptance in a broad variety of heavy industrial applications.


  • Phenoline 310

    Features:

    • Rapid cure-to-handle and cure-to-service characteristics
    • Low temperature (35°F) cure capabilities
    • Single coat application reduces labor costs
    • Ultra-high build capabilities provides a void-free film and excellent edge protection
    • Wide chemical resistance to acids, caustics and aliphatic solvents
    • Exceptional bond strength
    • Can be mat reinforced where exposure conditions dictate
    • VOC compliant to current AIM regulations

    Description:

    Single-coat, plural-component applied, ultra-high build coating for use on steel and concrete substrates where rapid cure characteristics are required. Phenoline 310 is applied by plural component spray equipment and offers the same high performance properties of Phenoline 309, yet in a quick-curing formulation.


  • Phenoline 311 Primer

    Features:

    • Approved for potable water, ANSI/NSF standard 61*
    • Low temperature cure (20°F)
    • Excellent blast-hold protection
    • Suitable for use over damp concrete
    • Excellent application characteristics
    • Fast recoat times
    • Moisture tolerance during application
    • Meets VOC restrictions
    • Low HAP’s content

    Description:

    A tank lining holding primer that has a variety of attributes including low-temperature cure, fast recoat times, moisture tolerance during application and cure, and excellent blast-hold protection. Phenoline 311 Primer is often used with thick film lining systems as a holding primer (maintain blast cleaning) and is suitable for both new tanks and relines. It exhibits excellent surface wetting characteristics and quick cure for handling. It contains high levels of inert flake reinforcement. Excellent for use as a bonding primer for linings when damp concrete or masonry substrates are encountered.


  • Phenoline 333

    Features:

    Description:

    Phenoline 333 is a low bake, high solids, modified epoxy formulated for use as a protective lining with excellent resistance to molten sulfur. Excellent chemical and thermal shock resistance.


  • Phenoline 341

    Features:

    • Single coat, high performance protection
    • Low to no odor
    • Easy to apply by standard equipment
    • Excellent chemical resistance
    • Fast cure
    • Tough abrasion resistant film
    • Suitable for potable water use (complies with ANSI/NSF Standard 61) *
    • Excellent flexibility
    • Excellent corrosion protection
    • Impact resistant
    • Hi-build application in one coat
    • Low temperature cure (35°F)

    Description:

    Phenoline 341 is a solventless epoxy lining for a variety of cargos including water, potable water, wastewater, seawater, fuels, crude oils, and other solutions. It is applied by standard airless spray equipment, as a single coat lining for ballast tanks or other storage vessels. It is acceptable for use as a lining for potable water tanks of 75 gal or larger and pipe diameters of 16 inches or larger.


  • Phenoline 353

    Features:

    • Outstanding overall chemical resistance
    • Dense, highly cross-linked film for superior barrier protection
    • Excellent abrasion resistance and toughness
    • Well-suited for hydrocarbon exposures
    • Low temperature cure version available

    Description:

    Phenoline 353 is a highly cross-linked epoxy lining with extraordinary overall chemical resistance and versatility. It has a unique blend of resins that make it highly resistant to a variety of aggressive cargos like gasoline, gasoline blends, biodiesel, fuel oils, and others. It can be used is both acidic and high temperature caustic exposures. Markets served are terminals, refineries, petrochemical, wastewater, railcar linings, and many others.


  • Phenoline 353 LT

    Features:

    • Outstanding overall chemical resistance
    • Dense, highly cross-linked film for superior barrier protection
    • Excellent abrasion resistance and toughness
    • Well-suited for hydrocarbon exposures
    • Cures down to 35°F (2°C)

    Description:

    Phenoline 353 LT is a highly cross-linked epoxy lining with extraordinary overall chemical resistance and versatility. It has a unique blend of resins that make it highly resistant to a variety of aggressive cargos like ethanol, gasolines, gasoline blends, biodiesel, fuel oils, and others. It can be used is both acidic and high temperature caustic exposures. Markets served are terminals, refineries, petrochemical, wastewater, railcar linings, and many others. This low temperature cure formulation allows application and curing down to 35°F (2°C).


  • Phenoline 379

    Features:

    • Single coat application reduces labor costs
    • Ultra-high build capabilities provides a voidfree film and excellent edge protection
    • Resistant to inorganic and organic acids, caustics and most solvents
    • Can be mat reinforced where exposure conditions dictate
    • Application by airless spray equipment (plural component acceptable but not required)
    • VOC compliant to current AIM regulations

    Description:

    Single-coat, airless-applied, ultra-high build coating for use on steel and concrete substrates subject to aggressive chemical exposure. Phenoline 379 has the same application and physical properties of Phenoline 309 but provides enhanced chemical protection for a broader and more concentrated range of acids.


  • Phenoline 380

    Features:

    • Rapid cure-to-handle and cure-to-service characteristics
    • Single coat application reduces labor costs
    • Ultra-high build capabilities provide a void-free film and excellent edge protection.
    • Resistant to inorganic and organic acids, caustics and most solvents
    • Exceptional bond strength
    • Can be mat reinforced where exposure conditions dictate
    • VOC compliant to current AIM regulations

    Description:

    Single-coat, plural-component applied, ultra-high build coating for use on steel and concrete substrates where rapid cure characteristics are required. Phenoline 380 has the same application and physical properties of Phenoline 379 but also provides rapid cure to handle and cure characteristics.


  • Phenoline 385

    Features:

    • High solids; Low VOC formula
    • VOC compliant to current AIM regulations
    • Excellent for crude-oil storage
    • Excellent resistance to petroleum products
    • Excellent abrasion resistance
    • Excellent thermal shock resistance
    • Passes EI 1541 jet fuel gum test

    Description:

    High performance, high solids, epoxy lining that is recommended for a variety of petroleum storage products including 180°F (82°C) crude oil, demineralized water 150°F (65°C), crude/water mixtures, fuel oil, jet fuel, biodiesel, and gasoline. It is also a good choice for wastewater and water exposures. Product is self-priming and is normally applied in two coats. It is also suitable for food-grade (aqueous) cargos and meets the FDA requirements for 21CFR 175.300 for direct food contact.


  • Phenoline Tank Shield

    Features:

    • Batch mix formulation, single leg airless spray
    • High impact resistance
    • Superior adhesion to steel
    • Excellent resistance to water and salt water
    • Resistance to a broad range of fuels
    • Passes EI 1541 jet fuel gum test
    • Resistant to hot water up to 180°F (82°C)
    • Excellent abrasion resistance and flexibility
    • Can be applied down to 35 °F (2 °C)
    • Can be applied as a single or multi-coat system
    • Non-blushing with a long recoat window
    • Low odor
    • Suitable for potable water use (complies with ANSI/NSF Standard 61*)

    Description:

    This product is a solvent-free, high performance epoxy coating designed as an internal tank, valve and pipe lining for chemical or other commodity storage. It is a unique blend of resins and curing agents that allow batch mixing for ease of application. Plural component spray equipment is not required. The product is blush resistant and is typically applied at film thicknesses of 20 mils (500 microns) or thicker as needed (tank floors). It can handle exposures typically seen in the oil and gas industries; crude oils and fuels. It is resistant to NGL condensates, produced water, brines, and industrial process water.


  • Phenoline Tank Shield Plus

    Features:

    • Excellent petrochemical resistance (fuels and crude)
    • High impact resistance
    • Superior adhesion to steel
    • Excellent hot water resistance
    • Excellent abrasion resistance
    • Can be applied as low as 35°F/2°C
    • Tolerates low temperature excursions to 20°F/-7°C during cure
    • Can be applied as a one-coat 20-60 mil system
    • Recommended as a petroleum tank bottom lining per API recommended practice 652.
    • Tank Shield Plus is a thick film reinforced lining proven to provide integrity at 50 mils or greater where bottom side perforations may occur.
    • Non-blushing, single or multi-coat system
    • Approved for potable water use

    Description:

    This product is a solvent free, low temperature cure, high performance epoxy lining designed to handle common cargoes in the oil and gas industry including crude oil, gasoline, jet fuels, and diesel. It is resistant to NGL condensates, produced water, brines, and industrial process water. It can handle deionized water up to 180°F (82°C) and is applied at film thicknesses of 20-60 mils (500-1500 microns) in a non-blushing, single coat application. Tank Shield Plus has good elongation and proprietary reinforcement which enables it to bridge perforations which may occur from bottom side corrosion. Tank Shield Plus remains water tight over a hole in 2 atmospheres of head pressure. This product is also approved for use in potable water applications with tanks larger than 1000 gallons or pipes diameters larger than 12 inches.


  • Plasite 3070

    Features:

    • Superior resistance to acids and solvents
    • Conforms to many of the current VOC regulations
    • Meets the requirements of the U.S. Food and Drug Administration, 21 CFR 175.300 for use in direct food contact areas.

    Description:

    A bake coating using an unmodified phenolic resin with superior resistance to acids and solvents. Conforms to many of the current VOC regulations.


  • Plasite 3073

    Features:

    • High solids, Low VOC formula
    • Excellent abrasion resistance
    • Resistant to a wide range of acids, chemicals, and solvents
    • Excellent thermal shock resistance
    • Resistant to concentrated sulfuric acid
    • Excellent for transportation equipment

    Description:

    A high solids phenolic lining offering superior resistance to acids, chemicals, solvents and salts. Conforms to FDA Title 21 CFR 175.300. Formerly: Lithcote® 73H.


  • Plasite 4006

    Features:

    Description:

    As a chemical-resistant coating for tank lining service and as a maintenance coating to protect against cor¬rosive conditions encountered in waste treatment, chemical/food processing and carbon filters. When combined with abrasive conditions, use PLASITE 4006HAR.


  • Plasite 4007

    Features:

    • Excellent resistance to organic and inorganic acids, salts, gasoline and crude oil

    Description:

    PLASITE 4007 is a high chemical resistant coating. May be used as a light colored topcoat for 4300 or as a multi-coat coating system with or without the option of incorporating fiberglass cloth reinforcement.


  • Plasite 4110

    Features:

    Description:

    Vinyl ester resin combined with special curing system and inert flake pigment to provide outstanding chemical and physical properties. Specially formulated for excellent abrasion resistance. PLASITE 4110 meets the FDA requirements for 21 CFR, 175.300 and 177.2420. Uses: As a high chemical abrasion-resistant thick film for tank lining service and as a maintenance coating for severe exposure.


  • Plasite 4301 HT

    Features:

    • Outstanding resistance to aggressive chemicals
    • Suitable for use as a highly chemically resistant lining
    • Excellent for splash, spill and film exposures on structural steel
    • Glass-flake reinforced film
    • High tensile and flexural strength
    • High film thickness

    Description:

    This high performance glass-flake filled coating was designed for application over steel or concrete in extreme chemical exposures. It is resistant to a wide variety of aggressive chemicals, including organic and inorganic acids, most alkalies, and many solvents. It is ideally suited for immersion service as internal steel tank linings, as well as for aggressive chemical splash, spill, and fume exposures on structural steel. Typical uses include steel tank and vat linings, secondary containment, structural steel, process floors, grating, sumps and trenches, scrubbers, and clarifiers.


  • Plasite 4310

    Features:

    • Outstanding acid immersion performance
    • Solvent immersion lining
    • Conductive film
    • High temperature resistance
    • Performs under thermal shock
    • Extremely high abrasion resistance
    • self priming
    • High build

    Description:

    Plasite 4310 is a vinyl ester resin combined with special curing system and inert flake pigment to provide outstanding chemical and physical properties. Plastic 4310 is specially formulated for excellent abrasion resistance while retaining temperature, chemical and other physical properties of Plasite 4300.


  • Plasite 4500

    Features:

    • High impact resistance
    • Superior adhesion to steel
    • Resistance to a broad range of chemicals
    • Can be applied as low as 35°F/2°C
    • Can be applied as a one-coat 20-60 mil system

    Description:

    PLASITE 4500 is a solvent free, flake-reinforced, high performance epoxy coating designed as an internal tank lining for chemical or other commodity storage. It is resistant to a broad range of chemicals such as fuels, salts, alkalis, many acids and some solvents. It is suitable for use in potable water tanks/piping conforming to ANSI/NSF Standard 61 for drinking water components. It also meets AWWA C210 specification.


  • Plasite 4500 FS

    Features:

    • Quick walk on time
    • Fast return to service
    • Excellent edge retention
    • Superior adhesion to steel
    • Resistance to a broad range of chemicals
    • Will cure down to 20°F/-7°C
    • Can be applied as a single-coat 20-60 mil system
    • Passes EI 1541 jet fuel gum test.

    Description:

    PLASITE 4500 FS is a solvent-free, edge retentive and high performance epoxy coating designed as an internal tank lining for chemical or other commodity storage. It is a two-component system applied by plural component spray equipment, at film thicknesses of 20-60 mils (500-1500 microns) in a monolithic application. It is particularly suited for petroleum-based cargoes including crude oil; fuel oils and gasoline storage. It has extremely fast cure times for turnaround projects that require placing back in service quickly and will cure down to 20F(-7C). The product has a unique ability to be applied as a prime coat and immediately back-rolled after spraying. This is recommended to treat pitted steel, weld areas, and the like. A second coat can be applied right after the prime coat using the same product for a “two-coat” yet monolithic application.


  • Plasite 4500 S

    Features:

    • High impact resistance
    • Superior adhesion to steel and concrete
    • Resistance to a broad range of chemicals
    • Can be applied in a one-coat application up to 60 mils
    • Can be sprayed using single component airless equipment
    • VOC compliant
    • *NSF 61 certified

    Description:

    Plasite 4500 S is a 100% solids, flake-filled, premium epoxy coating designed for internal steel and concrete tanks and pipe lining. It is a two component system consisting of four-parts by volume of Part A resin and one part by volume of Part B hardener. It is applied by plural component or single component spray equipment, in a one-coat application (20-60 mils) for internal lining applications. It also meets AWWA C210 specification.


  • Plasite 4503

    Features:

    • Outstanding wetting properties
    • Quick walk on time
    • Fast recoat time and return to service
    • Superior adhesion to steel
    • Resistance to a broad range of chemicals
    • Can be applied to substrate as low as 35°F/2°C
    • Suitable for use with a variety of lining systems

    Description:

    Plasite 4503 is a solvent-free, highly wetting (penetrating), high performance epoxy coating designed as a primer for internal tank linings for chemical or other commodity storage. It is ideally suited as a primer for both new steel and tank relines where severely pitted steel bottoms are common. It has exceptional chemical resistance properties and is recommended with an appropriate topcoat for petroleum-based cargoes including crude oil; fuel oils, gasoline and gasoline blends. It has extremely fast cure times for turnaround projects that require placing the tank back in service quickly. The product has a unique ability to be applied as a prime coat for severely pitted steel for complete coverage while providing a suitable base coat for subsequent lining systems.


  • Plasite 4550

    Features:

    • High Impact Resistance
    • Superior adhesion to metal substrates and concrete
    • Outstanding adhesion to stainless steel, even with low blast profiles
    • Well suited to protect alloy steels typically used to wet FGD systems where pitting and crevice corrosion often occur
    • Fast cure-to-service; depending upon application can be placed into service within 36 hours
    • Minimal blushing characteristics
    • Can be applied in temperatures as low as 35 °F (1.7 °C)
    • Can be applied as a one-coat system
    • Tested and approved for crude oil storage and transport up to 350 °F (177 °C)
    • Superior thermal shock resistance from -40 to 350 °F (-40-177 °C)
    • Complies with the API RP 652 definition of a reinforced liner.

    Description:

    PLASITE 4550 is a 100% solids, reinforced, premium novolac epoxy coating for internal tank lining. It is resistant to a broad range of chemicals such as fuels, salts, alkalis, strong inorganic acids, some solvents, sour crude oil and 98% sulfuric acid.


  • Plasite 4550 S

    Features:

    • High impact and thermal shock resistance
    • Superior adhesion to steel and concrete
    • Resistance to a broad range of chemicals
    • Can be applied up to 60 mils in one coat
    • Can be sprayed using single component airless equipment

    Description:

    PLASITE 4550 S is a 100% solids, flake filled, premium novolac epoxy coating designed for internal steel and concrete substrates. It is a two component system consisting of four-parts by volume of Part A resin and one part by volume of Part B hardener. It is applied by plural component or single component spray equipment, from a total thickness of 20-60 mils (500-1500 microns) in a single coat application for a variety of applications. This product has been tested and is approved for crude oil storage and transportation up to 350°F (177°C). It has superior thermal shock resistance over the range -40° to 350°F (-40 to 177°C). Typical Uses: Crude oil tankers, chemical storage tanks, wastewater clarifiers, plating vats, oil storage tanks, catwalks, pulp and paper liquor tanks or concrete exposures in wastewater applications.


  • Plasite 5302

    Features:

    • Cures quickly
    • Form an exceptionally tough, impact and abrasion resistant surfaces
    • Excellent adhesion to concrete, steel and wood
    • Non-shrinking
    • Minimum down time
    • Excellent resistance to water, oil, brine, most acids and alkalies

    Description:

    Plasite 5302 is an epoxy monolithic liner formulated for chemical and abrasion resistance in continuous immersion service.


  • Plasite 5371

    Features:

    • Trowel or spray applied
    • Non-sagging liner
    • Can be applied to steel or concrete (damp or dry)
    • Protective liner in one coat application on vertical, horizontal or overhead surfaces

    Description:

    Formulated for optimum chemical resistance to the chemical exposures found in the immersion and highly corrosive environments of municipal wastewater treatment.


  • Plasite 7122

    Features:

    • Versatile coating with wide chemical resistance
    • Excellent abrasion resistance
    • Excellent thermal shock resistance
    • Excellent resistance to fuels
    • Long history of performance
    • Self-priming

    Description:

    This lining-grade epoxy has wide chemical resistance and is suitable for use as a chemically resistant coating for aggressive atmospheric exposures or as a lining for a variety of chemical exposures. It is suitable for use in food-grade service where product purity (taste and odor) are critical. It has excellent abrasion and thermal shock resistance.


  • Plasite 7122 HAR

    Features:

    • Versatile coating with wide chemical resistance
    • Outstanding abrasion resistance
    • Excellent thermal shock resistance
    • Excellent resistance to fuels
    • Long history of performance
    • Self-priming

    Description:

    This lining-grade epoxy has wide chemical resistance and is suitable for use as a chemically resistant coating for aggressive atmospheric exposures or as a lining for a variety of chemical exposures. It is suitable for use in food-grade service where product purity (taste and odor) are critical. Specially formulated with high abrasion resistant fillers for outstanding abrasion and thermal shock resistance.


  • Plasite 7122 TFE

    Features:

    • Versatile coating with wide chemical resistance
    • Excellent abrasion resistance
    • Excellent thermal shock resistance
    • Excellent resistance to fuels
    • Long history of performance
    • Self-priming

    Description:

    This lining-grade epoxy has wide chemical resistance and is suitable for use as a chemically resistant coating for aggressive atmospheric exposures or as a lining for a variety of chemical exposures. It is suitable for use in food-grade service where product purity (taste and odor) are critical. It has excellent abrasion and thermal shock resistance. It has superior release properties to reduce or avoid issues with product cargoes such as sticking, hang-ups or bridging.


  • Plasite 7122 VAR

    Features:

    • Excellent overall chemical resistance to a wide range of acids, alkalies and solvents.
    • Superior abrasion resistance and good flexibility
    • Complies with FDA 21CFR 175.300 criteria for food contact

    Description:

    A cross linked epoxy-phenolic cured with a polyamine curing agent. Formulated with particular attention to wide chemical resistance and ease of handling. Plasite 7122 VAR, is an abrasion resistant tank lining and industrial maintenance coating.


  • Plasite 7122 VOC

    Features:

    • Excellent overall chemical resistance to a wide range of acids, alkalies and solvents.
    • Very good abrasion resistance and flexibility
    • Complies with FDA 21CFR 175.300 criteria for food contact

    Description:

    A cross linked epoxy-phenolic cured with a polyamine curing agent. Formulated with particular attention to wide chemical resistance and ease of handling. Plasite 7122 VOC is used as a tank lining and for industrial maintenance.


  • Plasite 7122 VTF

    Features:

    • Excellent overall chemical resistance to a wide range of acids, alkalies and solvents.
    • Smooth non-stick surface.
    • Very good abrasion resistance and flexibility.
    • Complies with FDA 21CFR 175.300 criteria for food contact.

    Description:

    A cross linked epoxy-phenolic cured with a polyamine curing agent. Formulated with particular attention to wide chemical resistance and ease of handling. Plasite 7122 VTF, is a PTFE filled tank lining for use where the surface requires release properties to reduce product sticking and bridging.


  • Plasite 7133

    Features:

    • Uses: Primarily as a tank lining and equipment coating material For the food and beverage industries.
    • Note: When properly applied and force cured, PLASITE 7133 will not impart taste or odor to such products as sugar solutions, wine, beer, meat products, and similar items. This coating is resistant to the standard cleaning for sanitation purposes and will withstand normal atmospheric steam cleaning procedures.

    Description:

    A combination of epoxy and polyamide type resins with selected pigments designed specifically as a high chemical resistant, non-toxic, odorless coating.


  • Plasite 7133 HS

    Features:

    • Plasite 7133 HS will not impart taste or odor to such products as sugar solutions, wine, beer, meat products and similar items.
    • This coating is resistant to the standard cleaning for sanitation purposes and will withstand normal atmospheric steam cleaning procedures.
    • Plasite 7133 HS meets the FDA requirements for 21 CFR 175.300 for direct aqueous food contact.

    Description:

    A combination of epoxy and polyamide resins with selected pigments designed specifically as a high chemical resistant, non-toxic, odorless coating.


  • Plasite 7159

    Features:

    • Easy-to-apply high performance thin film lining
    • Protects I high temperature demineralized water immersion - 212°F (100°C)
    • Recommended in high pressure three phase service up to 250°F (121°C)
    • Resists strong oxidizer and acid immersion
    • Can be air dried or force cured for prompt service

    Description:

    A water-resistant epoxy coating polymerized with a polyamine type curing agent. A high performance lining for elevated temperature and pressure immersion services in high purity water, as well as the oil/water separating processes encountered in the petroleum industry.


  • Plasite 7159 HAR

    Features:

    • Easy-to-apply high performance thin film lining
    • Protects I high temperature demineralized water immersion - 212°F (100°C)
    • Recommended in high pressure three phase service up to 250°F (121°C)
    • Resists strong oxidizer and acid immersion
    • Can be air dried or force cured for prompt service
    • Outstanding abrasion resistance

    Description:

    A water-resistant epoxy coating polymerized with a polyamine type curing agent. A high performance lining for elevated temperature and pressure immersion services in high purity water, as well as the oil/water separating processes encountered in the petroleum industry. This HAR version of Plasite 7159 is extremely abrasion resistant.


  • Plasite 9060

    Features:

    • Excellent overall chemical resistance to a wide range of acids, alkalies and solvents
    • Very good abrasion resistance and flexibility
    • Complies with FDA 21 CFR 175,300 criteria for food contact

    Description:

    A high solids modified epoxy cured with an amine adduct curing agent. Designed specifically as a highly chemical-resistant, non-toxic, tank lining.


  • Plasite 9060 LT

    Features:

    • Outstanding overall chemical resistance
    • Dense, highly cross-linked film for superior barrier protection
    • Superior immersion resistance
    • Excellent abrasion resistance and toughness
    • Well-suited for hydrocarbon exposures
    • Formulated for use in a large variety of facilities including waste water, chemical and fuel storage, wet-gas pipelines, rail cars, barges and ship tanks
    • Bis A free
    • Cures down to 35°F (2°C)

    Description:

    Plasite 9060 LT is a high performance tank lining with curing characteristics allowing the coating to be applied and cure at temperatures as low as 35°F (2°C) while achieving unmatched chemical resistance in caustic, acid, solvent and ethanol service. The diversity of chemical resistance and unique low temperature curing allows the owner flexibility with their equipment. For industrial use only.


  • Plasite 9081

    Features:

    Description:

    A high solids modified epoxy cured with a polyamine curing agent. Formulated with particular attention to chemical resistance and ease of handling. Primarily used as an industrial tank lining.


  • Plasite 9145 TFE

    Features:

    • Excellent resistance to a wide range of latex resin solutions

    Description:

    A high solids epoxy cured with an amine curing agent. Formulated with particular attention to latex resin resistance with special modification to provide superior release properties. Plasite 9145 TFE is used as a second coat over Plasite 9145 when additional release properties are desired or required.


  • Plasite 9570 TFE

    Features:

    • Meets the requirements of US Food & Drug Regulations 21 CFR 175.300
    • Accepted by the US EPA for use on surfaces which contact potable water
    • Excellent chemical resistance to all caustic solutions up to 200 °F (93 °C) and to a wide range of acids, solvents and water solutions

    Description:

    Plasite 9570 TFE is a highly resistant film for chemical tank lining service. Plasite 9570 TFE is specifically formulated to provide greater release properties to aid in the prevention of product hang-up or bridging problems.


  • Polyclad 757

    Features:

    • Resistant to corrosion caused by MIC and hydrogen sulfide
    • Outstanding abrasion and impact resistance
    • Fast curing
    • Low temperature cure
    • Superior wetting properties
    • Excellent adhesion to steel and DIP
    • Mix ratio of 1:1 and user friendly application properties.
    • Unlimited build with single multi-pass coats.
    • Self priming
    • Meets AWWA C222

    Description:

    Polyclad 757 is a high performance pipe lining specially designed for the protection of steel, concrete and DIP pipeline interiors. Typical applications are pipeline interiors for raw water transmission, wastewater transmission and treatment (Municipal and Industrial. Polyclad 757 provides protection against microbiologically induced corrosion (MIC) and hydrogen sulfide corrosion found in wastewater treatment service.


  • Polyclad 767

    Features:

    • Fast curing rate increases throughput
    • Superior wetting properties result in better edge retention and excellent adhesion to steel
    • Mix ratio of 1:1 and user friendly application properties
    • Unlimited build with single multi-pass coats
    • Approved for potable water use
    • Self priming (120 mil maximum for potable water)
    • Meets AWWA C222

    Description:

    Polyclad 767 is a high performance pipe coating specially designed for the protection of pipeline interiors. Typical applications are pipeline interiors for water transmission, wastewater treatment (municipal and industrial), and interior tank linings.


  • Polyclad 777 Fast-Set

    Features:

    • Fast curing rate increases throughput
    • Excellent abrasion resistance
    • Superior wetting properties for outstanding adhesion
    • Mix ratio 1:1 and user friendly application properties
    • Can be topcoated with Carbothane series of products
    • Unlimited build with single multi-pass coats
    • Compliant with AWWA C222

    Description:

    Polyclad 777 Fast Set is a high performance 100% solids structural polyurethane designed to provide superior corrosion protection for steel, ductile iron and concrete pipe. Tenacious adhesion and high impact resistance allow its use in the harshest environments. It forms a dense, long-term impermeable barrier that is ready for service moments after application through a snap-set cure mechanism. Typical uses include steel pipeline exteriors, steel valves & fittings, steel pilings, steel poles (above & below ground), buried tank exteriors, penstocks. No primer is required. Available in snap, fast, medium and slow set times.


  • Polyclad 777 Medium-Set

    Features:

    • Fast curing rate increases throughput
    • Excellent abrasion resistance
    • Superior wetting properties for outstanding adhesion
    • mix ratio 1:1 and user friendly application properties
    • Can be topcoated with Carbothane series of product
    • Unlimited build with single multi-pass coats
    • Compliant with AWWA C222

    Description:

    Polyclad 777 Medium Set is a high performance 100% solids structural polyurethane designed to provide superior corrosion protection for steel, ductile iron and concrete pipe. Tenacious adhesion and high impact resistance allow its use in the harshest environments. It forms a dense, long-term impermeable barrier that is ready for service moments after application through a snap-set cure mechanism. Typical uses include steel pipeline exteriors, steel valves & fittings, steel pilings, steel poles (above & below ground), buried tank exteriors, penstocks. No primer is required. Available in snap, fast, medium and slow set times.


  • Polyclad 777 PL

    Features:

    • Fast curing increases throughput
    • Excellent abrasion resistance
    • Superior wetting properties for outstanding adhesion
    • Mix ratio of 1:1 with easy application properties
    • Can be topcoated with Carbothane series of products
    • Unlimited film build with single or multi-pass coats

    Description:

    Polyclad 777 PL is a high performance 100% solids structural polyurethane designed to provide superior corrosion protection for steel, ductile iron and concrete pipe. Tenacious adhesion and high impact resistance allow its use in the harshest environments. It forms a dense, long-term impermeable barrier that is ready for service moments after application through a fast-set cure mechanism. No primer is required.


  • Polyclad 777 Slow-Set

    Features:

    • Fast curing increases throughput
    • Excellent abrasion resistance
    • Superior wetting properties for outstanding adhesion
    • Mix ratio 1:1 and user friendly application properties
    • Can be topcoated by Carbothane series of products
    • Unlimited build with single multi-pass coats
    • Compliant with AWWA C222

    Description:

    Polyclad 777 Slow Set is a high performance 100% solids structural polyurethane designed to provide superior corrosion protection for steel, ductile iron and concrete pipe. Tenacious adhesion and high impact resistance allow its use in the harshest environments. It forms a dense, long-term impermeable barrier that is ready for service moments after application through a snap-set cure mechanism. Typical uses include steel pipeline exteriors, steel valves & fittings, steel pilings, steel poles (above & below ground), buried tank exteriors, penstocks. No primer is required. Available in snap, fast, medium and slow set times.


  • Polyclad 777R

    Features:

    • Low temperature cure
    • Quick cure to handle
    • Superior wetting properties and outstanding adhesion to steel
    • Excellent edge retention
    • Mix ratio of 1:1 and user friendly application properties
    • Up to 80 mils build with a single application
    • Can be topcoated with Carbothane series of products for long-term color and gloss retention

    Description:

    Polyclad 777 R is a high performance, 100% solids structural polyurethane designed to repair Polyclad 777 or 777 PL when it has been damaged. It can be used on steel pipe exteriors, coating girth welds on steel pipe and other repairs as recommended.


  • Polyclad 951

    Features:

    • Improves flow efficiency in gas pipes
    • Excellent flow and leveling
    • Single-coat application
    • Hard, smooth, glossy finish
    • Excellent abrasion resistance
    • Meets all criteria of API RP 5L2
    • Long pot life

    Description:

    Polyclad 951 flowliner is an epoxy lining for “dry” natural gas transmission pipelines. It is designed to increase flow efficiency of natural gas in pipelines. This lining provides a smooth surface inside the pipe that will increase flow and reduce energy cost of transporting natural gas. Polyclad 951 offers corrosion protection of pipes during storage. It fully meets criteria of API RP 5L2 for gas transmission pipelines.


  • Polyclad 952

    Features:

    • Improves flow efficiency in gas pipes
    • Excellent flow and leveling
    • Single-coat application
    • Hard, smooth, glossy finish
    • Excellent abrasion resistance
    • Meets all criteria of API RP 5L2
    • Corrosion prevention during storage

    Description:

    Polyclad 952 flowliner is an epoxy lining for “dry” natural gas transmission pipelines. It is designed to increase flow efficiency of natural gas in pipelines. This lining provides a smooth surface inside the pipe that will increase flow and reduce energy cost of transporting natural gas. Polyclad 952 offers corrosion protection of pipes during storage. It fully meets criteria of API RP 5L2 for gas transmission pipelines.


  • Polyclad 956

    Features:

    • Improves flow efficiency in gas pipes
    • Meets API RP5L2 requirements for gas transmission pipeline flow liner
    • Excellent flow and leveling
    • Single-coat application
    • Hard, smooth, glossy finish
    • Excellent abrasion resistance
    • Corrosion prevention during storage

    Description:

    A solvent-less, high gloss, smooth epoxy coating for the lining of gas transmission pipelines. It’s hard, smooth surface aids in the flow of gas by reducing turbulence while protecting the interior surfaces from corrosion. It has excellent flow and wetting characteristics ideal for this type of application and use. Tested in accordance with API RP 5L2 for gas transmission pipelines.


  • Polyclad 975

    Features:

    • Quick dry to touch and QC times
    • Color indicator confirms proper mixing
    • Low temperature cure 40°F (4.4°C)
    • Excellent cathodic protection performance
    • Film build up to 50 mils DFT in one coat
    • Excellent edge retention
    • Superior adhesion to steel
    • Excellent adhesion over prepared FBE, epoxy and polyurethane coated pipe
    • Can be applied by spray, brush, roller or dual cartridge

    Description:

    Polyclad 975 is an advanced 100% solids, hybrid epoxy pipeline coating. Polyclad 975 has performance properties designed for corrosion protection of steel and ductile iron pipe exteriors, girth welds or tie-ins. It can be used for new pipe or rehabilitation of coated pipe. Polyclad 975 cures fast to allow quick QC and backfill times.Polyclad 975 is designed for spray application. Use Polyclad 975 H for hand applied applications.


  • Polyclad 975 H

    Features:

    • Quick dry to touch and QC times
    • Good brush and roll properties
    • Color indicator confirms proper mixing
    • Low temperature cure 40°F (4.4°C)
    • Excellent cathodic protection performance
    • Film build up to 30 mils DFT in one coat
    • Excellent edge retention
    • Superior adhesion to steel
    • Excellent adhesion over prepared FBE, epoxy and polyurethane coated pipe
    • Can be hand applied by brush or roller

    Description:

    Polyclad 975 H is an advanced 100% solids, hybrid epoxy pipeline coating. It has performance properties designed for corrosion protection of steel and ductile iron pipe exteriors, girth welds or tie-ins. Polyclad 975 H cures fast to allow quick QC and backfill times. H in 975 H stands for hand applied version. Polyclad 975 is the spray version.


  • Polyclad ARO

    Features:

    • Excellent gouge and abrasion resistance
    • High crosslink density results in tough film
    • Excellent adhesion to prepared FBE, Polyclad 975 and other coatings
    • Protects FBE, and other base coats during directional drilling applications
    • Zero VOCs, 100% solids
    • Apply up to 125 mils (3.2 mm) in one application
    • Rapid dry to handle, less than 20 minutes

    Description:

    Polyclad ARO is a high performance pipe coating specially designed for the protection of FBE coated pipeline from gouge and mechanical damage during directional drilling or slip bore installations. Polyclad ARO is applied directly over FBE as an abrasion resistant overlay (ARO) and provides superior protection in rocky, rough and mountainous environments. It absorbs the destructive energy and minimizes coating damage.


  • Pyroclad X1

    Features:

    • Full jet fire certification in accordance with ISO 22899
    • Excellent hydrocarbon pool fire protection (ISO 834/BS-476)
    • LR, DNV & ABS certification
    • Successfully passed Norsok M-501 System 5A environmental test program without a topcoat
    • Superior weathering resistance
    • Very low moisture absorption
    • Explosion resistance
    • Extremely durable, impact resistant finish
    • High film build properties
    • Low flame spread and smoke development

    Description:

    Pyroclad X1 is designed to provide jet fire and hydrocarbon fire protection for structural elements, beams, columns, bulkheads, underdecks and risers. Pyroclad X1 is suitable for applications in the industrial, petrochemical, oil and gas, offshore and refining industries.


  • Pyrocrete 239

    Features:

    • Combined acoustical and fire protection
    • Easily applied by spray or trowel
    • Excellent physical properties – hard, durable
    • Nonflammable – during or after application
    • Asbestos-free – complies with EPA and OSHA regulations
    • Chloride and sulfide free – no special priming required
    • Non-friable – high impact strength
    • Single package – mixed with clean, potable water at the job site
    • Investigated for exterior use by Underwriters Laboratories, Inc
    • Quality Manufactured – under strict Carboline quality standards
    • UL factory inspection service

    Description:

    A medium density, Portland cement based, cementitious fireproofing that is mixed with clean, potable water onsite before application and spray applied to the substrate. It provides 1-4 hour fire protection for structural steel, wood, bulkheads, and upgrades the fire resistance of existing concrete. It can also be used as a thermal barrier over polyurethane foam. Recommended areas of application include pharmaceutical facilities, pulp and paper mills, nuclear and conventional power plants, factories, warehouses, stadiums, institutional and biomedical facilities and acoustical applications.


  • Pyrocrete 241

    Features:

    • Over 39 years of proven performance
    • Exceptional durability and toughness
    • UL 1709 hydrocarbon fire rated up to 4 hours
    • BS 476 hydrocarbon fire rated up to 4 hours
    • ISO 22899-1 jet fire rated up to 2 hours
    • ASTM E119 cellulosic fire rated up to 4 hours
    • Cryogenic protection against LNG spills and immersion exposures
    • Resistant to 3 bar blast overpressure
    • Hose stream resistant
    • Tolerant to wide range of climates
    • Lightweight – one-fifth the weight of concrete for equal fire protection
    • Ideal for onsite and offsite application
    • Easy application by spray or trowel
    • Nonflammable – during or after application
    • Chloride and sulfide free – no special priming required
    • Asbestos-free – complies with EPA and OSHA regulations
    • Non-friable – high impact strength

    Description:

    A 55 lb./ft³ (881 kg/m³) density, Portland cement based, cementitious fireproofing. It provides both hydrocarbon and cellulosic fire protection for structural steel and can also be used to upgrade the fire resistance of existing concrete. Recommended areas of application include refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities.


  • Pyrocrete 241 HD

    Features:

    • Heavy duty, ultra high density formulation
    • Highest durability and toughness on the market
    • UL 1709 hydrocarbon fire rated up to 4 hours
    • ISO 22899-1 jet fire rated up to 2 hours
    • ASTM E119 cellulosic fire rated up to 4 hours
    • Cryogenic protection against LNG spills and immersion exposures
    • Resistant to 3 bar blast overpressure
    • Hose stream resistant
    • Tolerant to wide range of climates
    • Lightweight – one-fifth the weight of concrete for equal fire protection
    • Ideal for onsite and offsite application
    • Easy application by spray or trowel
    • Nonflammable – during or after application
    • Chloride and sulfide free – no special priming required
    • Asbestos-free – complies with EPA and OSHA regulations
    • Non-friable – high impact strength

    Description:

    A 70 lb./ft³ (1,121 kg/m³) density, Portland cement based, cementitious fireproofing. It provides both hydrocarbon and cellulosic fire protection for structural steel and can also be used to upgrade the fire resistance of existing concrete. Recommended areas of application include refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities.


  • Pyrocrete 241 HY

    Features:

    • Cost effective, high yield
    • Exceptional durability and toughness
    • UL 1709 hydrocarbon fire rated up to 4 hours
    • ISO 22899-1 jet fire rated up to 2 hours
    • Cryogenic protection against LNG spills and immersion exposures
    • Resistant to 3 bar blast overpressure
    • Hose stream resistant
    • Tolerant to wide range of climates
    • Lightweight – one-fifth the weight of concrete for equal fire protection
    • Ideal for onsite and offsite application
    • Easy application by spray or trowel
    • Nonflammable – during or after application
    • Chloride and sulfide free – no special priming required
    • Asbestos-free – complies with EPA and OSHA regulations
    • Non-friable – high impact strength

    Description:

    A 50 lb./ft³ (800 kg/m³) density, Portland cement based, cementitious fireproofing. It provides both hydrocarbon and cellulosic fire protection for structural steel and can also be used to upgrade the fire resistance of existing concrete. Recommended areas of application include refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities.


  • Pyrocrete 40

    Features:

    • Cost effective fireproofing solution
    • Outstanding coverage, high build
    • Exceptional durability and toughness
    • UL 1709 hydrocarbon fire rated up to 4 hours
    • BS 476 hydrocarbon fire rated up to 4 hours
    • ISO 22899-1 jet fire rated up to 2 hours
    • ASTM E119 cellulosic fire rated up to 4 hours
    • Cryogenic protection against LNG spills and immersion exposures
    • Resistant to 3 bar blast overpressure
    • Hose stream resistant
    • Tolerant to wide range of climates
    • Lightweight – one-fifth the weight of concrete for equal fire protection
    • Easy application by spray or trowel
    • Nonflammable – during or after application
    • Chloride and sulfide free – no special priming required
    • Asbestos-free – complies with EPA and OSHA regulations
    • Non-friable – high impact strength

    Description:

    A 40 lb./ft³ (640 kg/m³) density, Portland cement based, cementitious fireproofing. It provides both hydrocarbon and cellulosic fire protection for structural steel and can also be used to upgrade the fire resistance of existing concrete. Recommended areas of application include refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities.


  • Pyrocrete Hardcoat 4500

    Features:

    • Easily applied by spray or trowel
    • Lightweight - less than 3.5 lbs/ft² (17 kg/m²) for typical application
    • Excellent bonding properties
    • Hard, durable armour coat
    • Fast overcoat time over Pyrocrete materials

    Description:

    110 lbs/ft³ (1,762 kg/m³) high density armour coat that is applied over Pyrocrete materials to enhance durability in high abuse areas. Recommended areas of application include refineries, petrochemical, pharmaceutical facilities, pulp and paper mills, offshore platforms, nuclear and conventional power plants, factories, warehouses, institutional and biomedical facilities.


  • Pyrolite 15

    Features:

    • Durable cementitious formulation
    • Noncombustible
    • Can be injected with Accelerator A-20 for fast set and increased yield (optional)
    • Asbestos-free – complies with EPA and OSHA regulations.
    • Mineral Wool free – no airborne fibers.
    • Styrene free – no toxic decomposition gases.
    • Economical – Maintains project on budget.
    • Design flexibility with over 40 UL designs.

    Description:

    A 15 lbs./ft³ density SFRM intended for the fire protection of interior structural columns, beams, joists, decks, walls, roofs, girders, floors and pre-cast concrete units. It is tested and certified for fire resistance ratings up to 4 hours.


  • Reactamine 760

    Features:

    • UL approved for ANSI/NSF Std. 61 potable water
    • Complies with 21 CFR 175.300 Method D, E, & G and Direct Dry Food Contact
    • Complies with Greenbook
    • Cold temperature cure
    • Fast cure and walk on time
    • Excellent barrier properties, low permeability
    • Single-coat application 60 to 125 mils
    • Bridges normal shrinkage cracks in concrete
    • True monolithic film on steel and concrete
    • Encapsulates rivets, bolts, and edges in one coat
    • Outstanding abrasion, impact and tear resistance
    • Combines polyurethane and polyurea technologies to form a hybrid polyurethane

    Description:

    Environmentally friendly, advanced hybrid technology, plural-component applied coating used as a lining for water, wastewater, manholes, penstocks, dam gates, pipelines and other aggressive immersion applications. Provides protection against microbiologically induced corrosion (MIC) and hydrogen sulfide corrosion found in wastewater treatment service.


  • Reactamine 760 HB

    Features:

    • High film build (200 mil plus) in one coat
    • Complies to Greenbook
    • UL approved for potable water*
    • Cold temperature cure
    • Fast cure and walk on time
    • Excellent barrier properties, low permeability
    • Can be used to resurface highly deteriorated concrete
    • Bridges normal shrinkage cracks in concrete
    • True monolithic film on steel and concrete
    • Encapsulates rivets, bolts, and edges in one coat
    • Outstanding abrasion, impact and tear resistance
    • Combines polyurethane and polyurea technologies to form a hybrid polyurethane

    Description:

    Environmentally friendly, advanced hybrid technology, plural-component applied coating used as a lining for water, wastewater, manholes, penstocks, dam gates, pipelines and other aggressive immersion applications. Provides protection against microbiologically induced corrosion (MIC) and hydrogen sulfide corrosion found in wastewater treatment service. Ultra high build product designed to be applied at high thickness in one coat application.


  • Reactamine ET

    Features:

    • Tough abrasion and impact resistant film
    • High tensile strength and tear resistance
    • Excellent water and waste water resistance
    • Moisture tolerance; during and after cure
    • Low odor; zero VOC
    • Can be applied from 20 °F to 150 °F (-6 °C to 65 °C)
    • Extremely fast cure times (dries to the touch in 10 seconds)
    • Service temperature (dry) of -40 °F to 250 °F (-4 °C to 121 °C)
    • Single coat application (=250 mils)
    • Applies using a heated, plural component spray system
    • Complies with FDA 21CFR 175.300 criteria for dry food contact with and without Reactamine Primer 28

    Description:

    Reactamine ET is an extra tough, abrasion resistant elastomer coating with extremely fast cure times that is ideal for concrete substrates. It possess exceptional toughness for numerous industrial applications that include linings for wastewater applications, secondary containment, sewer lines, manhole restoration, rail cars, wastewater lagoon linings, and other applications needing a tough resilient coating. It is extremely resistant to high abrasion and impact with elongation properties to tolerate movement over concrete substrates.


  • Reactamine Primer 28

    Features:

    • Excellent bonding primer for polyurea topcoats over steel substrates
    • Excellent for sealing porous substrates like dry concrete

    Description:

    Reactamine Primer 28 is a single component resin formulation that is used as a bonding primer over a number of substrates including steel and concrete. It is particularly effective to promote adhesion of polyurea/polyurethane elastomers to steel substrates. It can also be used to prime and seal dry porous substrates such as concrete


  • Rustbond

    Features:

    • Universal primer and tie-coat
    • Excellent adhesion to SSPC-SP 2 prepared steel, galvanizing, aluminum, stainless steel and copper
    • Low stress, highly flexible film
    • Extremely high solids
    • Low odor
    • Contains corrosion inhibitors
    • Compatible with a variety of topcoats
    • User friendly brush and roller application
    • VOC compliant to current AIM regulations

    Description:

    Rustbond is a cross-linked penetrating primer/sealer with excellent wetting properties. It is highly flexible with good chemical and solvent resistance, and accept a variety of topcoats. Recommended use as primer/sealers for marginally prepared steel and over old coatings. Its excellent wetting properties allows it to penetrate rust and discontinuities in existing coatings and provide a firm anchorage for a variety of topcoats. Its thixotropic character reduces run off, ensuring that the edges of existing coatings are encapsulted thus reducing undercutting and peeling. It may also be used as a tie-coat for coatings that exceed their “recoat window.” Consult Carboline Technical Services Department for specific recommendations.


  • Rustbond FC

    Features:

    • Universal primer and tie-coat
    • Cures down to 35°F (2°C)
    • Excellent adhesion to SSPC-SP 2 prepared steel, galvanizing, aluminum, stainless steel and copper
    • Low stress, highly flexible film
    • Extremely high solids
    • Low odor
    • Contains corrosion inhibitors
    • Compatible with a variety of topcoats
    • User friendly brush and roller application
    • VOC compliant to current AIM regulations

    Description:

    Rustbond FC is a cross-linked penetrating primer/sealer with excellent wetting properties. It is highly flexible with good chemical and solvent resistance, and accept a variety of topcoats. Recommended use as primer/sealers for marginally prepared steel and over old coatings. Its excellent wetting properties allows it to penetrate rust and discontinuities in existing coatings and provide a firm anchorage for a variety of topcoats. Its thixotropic character reduces run off, ensuring that the edges of existing coatings are encapsulated thus reducing undercutting and peeling. It may also be used as a tie-coat for coatings that exceed their “recoat window.” Consult Carboline Technical Services Department for specific recommendations.


  • Sanitile 120

    Features:

    • Excellent primer/sealer for drywall
    • Glue-like bond to almost any surface
    • Outstanding tie-coat over existing coatings
    • Single component, thin-film application
    • Topcoat with virtually any generic coating
    • Ready-to-apply as supplied
    • Fast drying
    • Low odor; low VOC
    • Suitable for use in USDA inspected facilities

    Description:

    Universal bonding primer that adheres tenaciously to virtually any surface including difficult-to-coat substrates like galvanized and stainless steel, aluminum, PVC, FRP and ceramic tile. Designed for topcoating with most generic types.


  • Semstone 110

    Features:

    • Outstanding wetting properties
    • Solvent-free
    • Long working time
    • Excellent adhesion
    • Compatible with a variety of toppings

    Description:

    Two part epoxy exhibiting superior adhesion to concrete and steel. Used primarily as a primer/sealer for concrete surfaces and top coated with a variety of chemically resistant toppings.


  • Semstone 110 EP

    Features:

    • Outstanding wetting properties
    • Solvent-free
    • Long working time
    • Excellent adhesion
    • Compatible with a variety of toppings

    Description:

    Two part epoxy exhibiting superior adhesion to concrete and steel. Used primarily as a primer/sealer for concrete surfaces and top coated with a variety of chemically resistant toppings.


  • Semstone 140

    Features:

    • Excellent resistance to chemical attack
    • Excellent abrasion and impact resistance
    • Exceptional thermal shock resistance
    • Superior bonding properties
    • High cohesive strength
    • Low permeability
    • Low odor

    Description:

    High performance lining system designed for concrete. Semi-leveling coating which may be applied as an aggregate filled and/or reinforced coating system. Specially formulated to withstand some of industry’s most aggressive chemicals.


  • Semstone 140 CT

    Features:

    • Excellent resistance to chemical attack
    • Excellent abrasion and impact resistance
    • Exceptional thermal shock resistance
    • Superior bonding qualities
    • High cohesive strength
    • Low permeability
    • Low odor

    Description:

    Semstone 140CT is a 100% solids, high performance, epoxy lining system designed for concrete. Semstone 140CT is a semi-leveling coating which may be applied as an aggregate filled and/or reinforced coating system. Semstone 140CT is specially formulated to withstand some of industry’s most aggressive chemicals.


  • Semstone 145

    Features:

    • Excellent resistance to chemical attack
    • Excellent abrasion and impact resistance
    • Exceptional thermal shock resistance
    • Superior acid resistance
    • Superior bonding qualities
    • High cohesive strength
    • Low permeability
    • Low odor

    Description:

    100% solids, high performance, novolac epoxy lining system designed for concrete. It is a semi-leveling coating and may be applied as an aggregate filled and/or reinforced coating system. Specially formulated to withstand some of industry’s most aggressive chemicals, including 98% sulfuric acid, as well as many organic chemicals and solvents.


  • Semstone 145 CT

    Features:

    • Excellent resistance to chemical attack
    • Excellent abrasion and impact resistance
    • Exceptional thermal shock resistance
    • Superior bonding qualities
    • High cohesive strength
    • Low permeability
    • Low odor
    • Formulated to resist a variety of chemical solutions.
    • Suitable for use in USDA-inspected facilities

    Description:

    Semstone 145 CT is a 100% solids, high performance, novolac epoxy lining system designed for concrete. Semstone 145 CT is a semi-leveling coating which may be applied as an aggregate filled and/or reinforced coating system. Semstone 145 CT is specially formulated to withstand some of industry’s most aggressive chemicals, including 98% sulfuric acid, as well as many organic chemicals and solvents.


  • Semstone 145 SL

    Features:

    • Excellent resistance to chemical attack
    • Excellent abrasion and impact resistance
    • Exceptional thermal shock resistance
    • Superior adhesion to both steel or concrete
    • High cohesive strength
    • Low permeability
    • Low odor

    Description:

    Semstone 145 SL is a 100% solids, high performance, novolac epoxy coating designed for concrete. Semstone 145 SL is a self-leveling coating which may be applied as a neat, aggregate filled and/or reinforced coating system. Semstone 145 SL is specially formulated to withstand some of the industry's most aggressive chemicals, including 98% sulfuric acid as well as many organic chemicals and solvents.


  • Semstone 245

    Features:

    • Excellent resistance to chemical attack
    • Excellent abrasion and impact resistance
    • Exceptional thermal shock resistance
    • Superior bonding qualities
    • High cohesive strength
    • Low permeability
    • Low odor
    • Formulated to resist a variety of chemical solutions.

    Description:

    Semstone 245 is a 100% solids, high performance, novolac epoxy lining system designed for concrete. Semstone 245 is a semileveling coating, it may be applied as an aggregate filled and/or reinforced coating system. Semstone 245 is specially formulated to withstand some of the industry’s most aggressive chemicals, including chlorinated solvents.


  • Semstone 300

    Features:

    • Easy to apply
    • Nonflammable
    • Low odor
    • Castable
    • Make excellent materials of construction

    Description:

    Semstone 300 polymer concrete is an excellent alternative to acid brick. It is used to protect Portland cement concrete from attack from a wide range of aggressive chemicals. Semstone 300 polymer concrete can be applied from 1/2” (12.7 mm) to several inches thick. Applied by screed and trowel method, the installation is quick and easy. Semstone 300 provides a monolithic surfacing that has excellent resistance to impact and mechanical abuse and can be used to restore and protect degraded surfaces in a single application.


  • Semstone 6325 Sealant

    Features:

    • Long term abrasion and chemical resistance
    • Excellent bond strength assures good adhesion
    • Pourable viscosity allows easy installation to horizontal surfaces
    • Retains physical properties over a wide temperature range, -20 to 150°F (-29 to 66°C)
    • Factory proportioned packaging ensures consistent high quality and simplified mixing
    • Compatible with all Carboline lining systems

    Description:

    Two-component, self-leveling, polyurethane sealant. It exhibits excellent flexibility with moderate hardness and good chemical resistance to organic acids, alkalis and most solvents. Uses: can be used in conjunction with all lining systems in a wide range of applications. All high movement joints: isolation, expansion or control Thermal shock situations Exterior applications


  • Semstone 800 Series PM

    Features:

    • Excellent mechanical strengths
    • Rapid hardening
    • Excellent bond strength assures superior adhesion
    • Excellent chemical resistance
    • Easily installed to clean, sound substrate
    • Factory proportioned packaging ensures consistent high quality and simplified mixing
    • Easy to use, fast-setting, labor saving system

    Description:

    Semstone 800 Series Patching Mortar exhibits excellent bond strength and chemical resistance to most acids, alkalies, salt solutions and oils. Due to its non-sag, lightweight consistency, it is used to permanently patch and repair vertical and overhead voids.


  • Semstone 800 Series Primer

    Features:

    • Seals and penetrates concrete
    • Promotes adhesion of vinyl ester linings to concrete

    Description:

    800 Series Primer is a two-component, highly crosslinked vinyl ester priming system that penetrates into concrete and reduces porosity. It is applied to a properly prepared surface prior to the application of the appropriate Carboline lining system. The use of 800 Series Primer ensures a secure bond between the substrate and the lining system, reduces absorption of the lining system’s liquids by sealing concrete porosity and makes the overall application of the lining system easier.


  • Semstone 805

    Features:

    • Highly Flexible
    • Chemical Resistant
    • Water Resistant
    • Abrasion Resistant
    • 100% Solids

    Description:

    Semstone 805 is a flexible epoxy polymer coating and lining providing a chemical, water and abrasion resistant barrier for steel and concrete. This versatile coating system was developed as a self-leveling, flexible chemical resistant coating and lining and can also be used as a high build coating and lining system with the addition of a third component. Semstone 805 is a 100% solids, low odor, two-component system applied either as a neat system (unfilled), a reinforced system, an aggregate-filled system or as an aggregate filled reinforced system. A bagged Part C thixotropic agent is added for high build applications. It is most often used with reinforcing fabric (#100) over expansion joints.


  • Semstone 806

    Features:

    • Highly Flexible
    • Abrasion Resistant
    • Chemical Resistant
    • Water Resistant
    • 100% Solids

    Description:

    Semstone 806 is a 100% solids, low odor, rubberized epoxy. It is used as a chemically resistant coating for concrete. When reinforced with our flexible reinforcing fabrics it provides a system which will bridge working cracks as well as expansion joints. Semstone 806 reinforced with #100 fabric can bridge crack expansion joint movement up to 1/2” without cracking. Semstone 806, as packaged, is a self-leveling material. However, it maybe used as a high build coating system by the addition of a third component, Part C, which is a non-silica thixotrope (when using reinforcing fabric, Part C is not required). Concrete slabs with severe cracking problems, as well as all construction and expansion joints, may be treated using Semstone 806 with #100 Fabric is ideal for use as a secondary containment coating.


  • Semstone 870

    Features:

    • Excellent resistance to chemical attack
    • Excellent abrasion and impact resistance
    • Exceptional thermal shock resistance
    • Superior bonding qualities
    • High cohesive strength
    • Low permeability
    • Low odor

    Description:

    Semstone 870 is a high performance, vinyl ester lining system designed for concrete. Semstone 870 is a semi-leveling coating which may be applied as an aggregate filled and/or reinforced coating system. Semstone 870 is specially formulated to withstand some of industry’s most aggressive chemicals, including a broad range of organic chemicals. A cooler temperature version (870 CT) is available on special order.


  • Semstone 870 CT

    Features:

    • Excellent resistance to chemical attack
    • Excellent abrasion and impact resistance
    • Exceptional thermal shock resistance
    • Superior bonding qualities
    • High cohesive strength
    • Low permeability
    • Low odor

    Description:

    Semstone 870 is a high performance, vinyl ester lining system designed for concrete at cooler temperatures. Semstone 870 CT is a semi-leveling coating which may be applied as an aggregate filled and/or reinforced coating system. Semstone 870 CT is specially formulated to withstand some of industry’s most aggressive chemicals, including a broad range of organic chemicals.


  • Semstone 884

    Features:

    • Excellent alternative to acid brick

    Description:

    Semstone 884 is a vinyl ester polymer concrete which incorporates proprietary non-shrink technology into its formulation, making it the first practical vinyl ester polymer concrete for use as a concrete topping. It is recommended for use in concentrated nitric acid service and other strong oxidizers. Semstone 884 is an excellent alternative to acid brick. It is also used as a construction material for pouring pump foundations and small tank foundations. It can be used for pre-casting of sumps and trenches.


  • Splash Zone A-788

    Features:

    • Designed for underwater and other wet applications
    • Can be applied up to 2" in thickness
    • Self-priming on most surfaces and over most generic types of coatings
    • Rapid cure characteristics
    • VOC compliant to current AIM regulations

    Description:

    Solvent-free patching compound used for repairing pits, cracks and voids in steel, concrete, wood and other surfaces. Has the unique ability to be mixed, applied and cured underwater.


  • Thermaline 2954

    Features:

    • Will air dry at ambient
    • Resistant to severe thermal shock

    Description:

    For use as a high performance finish for surfaces in service from 300 °F (149 °C) to 800 °F (426 °C) with excellent resistance to thermal shock. It is typically used to prevent corrosion in service under insulation. For use over carbon steel, it can be applied over modified silicone primers or Carbozinc® 11 series.


  • Thermaline 2977

    Features:

    • Excellent “hot” application characteristics, may be applied over hot substrates up to 300°F (149°C)
    • Will air dry “tack free” at ambient but will remain soft until heat curing has been achieved
    • Typically topcoated with a silicone or modified silicone finish

    Description:

    A heat resistant primer for use on steel substrates that may reach up to 800°F (426°C).


  • Thermaline 4000

    Features:

    • Inorganic; stable; inert polymer
    • Outstanding durability
    • Excellent corrosion protection (used over Carbozinc inorganic primers)
    • High temperature resistance (800 °F [426 °C])
    • VOC compliant
    • Cures at ambient conditions (hard in 2 hours)
    • Cures down to 40 °F (4 °C)
    • Does not require heat cure for high-temp service
    • Outstanding resistance to handling damage
    • Single-package

    Description:

    Thermaline 4000 is a high heat polymer coating used for the protection of equipment operating at elevated temperatures. It is typically used over Carbozinc® inorganic zinc primers for outstanding corrosion protection and heat resistance. The combination of the zinc primer with this finish provides exceptional performance in durability. Unlike most high temperature silicone-based technologies with soft films, Thermaline 4000 does not require a heat cure for film forming properties. It cures hard rapidly under ambient conditions (humidity greater than 30%).


  • Thermaline 4000 Aluminum

    Features:

    • Inorganic; stable; inert polymer
    • Outstanding durability
    • Excellent corrosion protection (used over Carbozinc inorganic primers)
    • High temperature resistance (1000°F/538°C)
    • VOC compliant
    • Cures at ambient conditions (hard in 4 hours)
    • Cures down to 40°F
    • Does not require heat cure for high-temp service
    • Outstanding resistance to handling damage
    • Single-package

    Description:

    Thermaline 4000 Aluminum is a high heat polymer coating used for the protection of equipment operating at elevated temperatures. It is typically used over Carbozinc® inorganic zinc primers for outstanding corrosion protection and heat resistance. The combination of an inorganic zinc primer with this grey-aluminum finish provides exceptional performance in durability. Unlike most high temperature silicone-based technologies with soft films, Thermaline 4000 Aluminum does not require a heat cure for film forming properties. It cures hard rapidly under ambient conditions (humidity greater than 30%).


  • Thermaline 450

    Features:

    • Temperature resistance up to 450 °F (232 °C)
    • High-build single-coat capabilities
    • Excellent resistance to thermal shock
    • Superior abrasion and chemical resistance
    • through internal reinforcement
    • Ambient-temperature cure
    • VOC compliant to current AIM regulations

    Description:

    Highly cross-linked, glass-flake filled polymer that offers exceptional barrier protection and resistance to wet/dry cycling at elevated temperatures. Suitable for insulated or uninsulated pipes, stacks and equipment operating up to 450 °F (232 °C). This coating provides excellent resistance to corrosion, abrasion and permeation, and its novolac-modification resists severe chemical attack. This extreme performance product has decades of performance and is recommended for CS-1,3,4 and SS-1,2,3 systems of NACE SP0198 Standard Practice for coatings to control corrosion under insulation (CUI).


  • Thermaline 450 EP

    Features:

    • Continuous temperature resistance to 400°F(204°C)
    • Very good flexibility
    • Excellent overall chemical resistance
    • Very good abrasion resistance
    • Easily applied by spray
    • Acceptable for use over stainless steels
    • High solids, low VOC formula

    Description:

    A high performance immersion-grade coating system which has excellent resistance to wet/dry cycling conditions at elevated temperatures. It is typically used on hot steel substrates under insulation operating continuously up to 400°F/204°C. It has excellent chemical resistance properties to handle the corrosive effects of wet insulation under thermal cycling conditions. This product is recommended for CS-3 and SS-2 systems of NACE SP0198 Standard Practice for coatings to handle corrosion under insulation (CUI).


  • Thermaline 451

    Features:

    • Extreme chemical resistance
    • Excellent thermal shock resistance
    • Excellent internal film reinforcement
    • Excellent edge protection
    • Excellent abrasion/impact resistance

    Description:

    Thermaline 451 is a (MIO) flake filled cycloaliphatic amine cured epoxy phenolic novolac. This product has been formulated for use in immersion service in water and hydrocarbons such as fuel oil, diesel fuel, and gasoline. It may also be used under thermal insulation at elevated temperatures. Thermaline 451 has been modified with micaceous iron oxide (MIO) to provide excellent edge protection, one coat high build application properties, high temperature resistance and reinforced film properties. This product is self priming and resistant to 425-450 °F (218-232 °C).


  • Thermaline 4700

    Features:

    • Resistant to severe thermal shock
    • Provides outstanding long-term performance when applied over Carbozinc inorganic zinc primers
    • Air-dries to touch and provides barrier protection prior to heat curing (full film physical properties occur after heat curing)

    Description:

    High-performance finish for areas exposed to extreme temperatures. Suitable for service from 400°F-1000°F (204°C-538°C) Color stability at maximum temperature will depend on color selected. Requires heat curing.


  • Thermaline 4700 Aluminum

    Features:

    • Resistant to severe thermal shock
    • Provides outstanding long-term performance when applied over Carbozinc inorganic zinc primers
    • Air-dries to touch (full film formation properties occurs after heat curing)

    Description:

    High-performance finish for areas exposed to extreme temperatures. Suitable for service from 400°F-1000°F (204°C-538°C) Color stability at maximum temperature will depend on color selected. Requires heat curing.


  • Thermaline 4700 VOC Aluminum

    Features:

    • Resistant to severe thermal shock
    • Provides outstanding long-term performance when applied over Carbozinc inorganic zinc primers
    • Air-dries to touch (full film formation properties occurs after heat curing)
    • VOC Compliant

    Description:

    High-performance finish for areas exposed to extreme temperatures. Suitable for service from 400-1200 °F (204-649 °C).


  • Thermaline 4900

    Features:

    • Temperature resistance up to 500°F (260°C) for black **
    • Air-dried curing capabilities
    • Single-coat application
    • Excellent resistance to thermal shock
    • Good weathering and color stability
    • RTS colors available

    Description:

    Air-dried coating available in colors and suitable for high temperature exposures up to 500°F (260°C). Air-drying characteristics allow for faster handling of in-shop applications than with other high-temperature coatings. Heat cure above 300°F (149°C) is recommended and will impart added strength and integrity to the coating.


  • Thermaline 4900 Aluminum

    Features:

    • Temperature resistance up to 525°F (273°C)
    • Air-dried curing capabilities
    • Single-coat application
    • Excellent resistance to thermal shock
    • Good weathering and color stability

    Description:

    Air-dried coating available in colors and suitable for high temperature exposures up to 525°F (273°C). Air-drying characteristics allow for faster handling of in-shop applications than with other high-temperature coatings. Heat cure above 300°F (149°C) is recommended and will impart added strength and integrity to the coating.


  • Thermaline 4900 VOC

    Features:

    • Temperature resistance up to 500°F (260°C) for black **
    • Air-dried curing capabilities
    • Single-coat application
    • Excellent resistance to thermal shock
    • Good weathering and color stability
    • VOC compliant
    • RTS colors available

    Description:

    Air-dried coating available in colors and suitable for high temperature exposures up to 500°F (260°C). Air-drying characteristics allow for faster handling of in-shop applications than with other high-temperature coatings. Heat cure above 300°F (149°C) is acceptable and will impart added strength and integrity to the coating.


  • Thermaline 4900 VOC Aluminum

    Features:

    • Temperature resistance up to 525°F (273°C)
    • Air-dried curing capabilities
    • Single-coat application
    • Excellent resistance to thermal shock
    • Good weathering
    • VOC compliant

    Description:

    Air-dried coating suitable for high temperature exposures up to 525°F (273°C). Air-drying characteristics allow for faster handling of in-shop applications than with other high-temperature coatings. Heat cure above 300°F (149°C) is acceptable and will impart added strength and integrity to the coating.


  • Thermaline Heat Shield

    Features:

    • Unique reinforced but flexible polymer film
    • Versatile use from cryogenic to 1200°F (650°C) exposures
    • Dries to handle without heat cure (See curing schedule)
    • Outstanding barrier properties
    • Protects steel from thermal wet cyclic conditions
    • Suitable for both shop and field application
    • Provides corrosion protection even with ambient temperature cure
    • Meets ISO 12944-6 C5-M Medium
    • Self priming or apply over Carbozinc 11 primers when uninsulated
    • Protects stainless steels from chlorides and stress corrosion cracking
    • Very fast recoat times

    Description:

    This is an extreme performance coating for hot, cryogenic and cycling exposures. Thermaline Heat Shield contains a unique blend of plate-like reinforcing pigments fortified with an inert polymeric matrix. The resulting film provides an outstanding barrier against corrosives and harsh exposures typically seen in elevated temperature environments. This versatile coating is ideal for all piping, vessels and equipment operating from cryogenic conditions up to 1200°F. It is particularly well suited to prevent corrosion under insulated equipment/piping for both carbon steel substrates and stainless steels. This fortified coating has superior shop handling properties over standard silicone coatings (see Curing). It is recommended for CS-6 and SS-5 systems of NACE SP0198 Standard Practice for coatings to control corrosion under insulation (CUI).


  • Thermo-Lag 2000-P

    Features:

    • UL listed - designs for many types of steel sections up to 3 hour fire ratings for both interior and exterior environments.
    • Durable finish - provides a hard, durable finish resistant to normal wear.
    • Thin film coating - offers an economical solution to alternative fireproofing.
    • VOC compliant
    • Easy repair - if damaged it can be repaired easily using material as putty.

    Description:

    Thermo-Lag 2000-P is designed to fireproof steelwork for up to a 3 hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, tubes, pipes, vessel skirts, bulkheads, underdecks and electrical raceways.


  • Thermo-Lag 2000-SP

    Features:

    • UL listed - designs for many types of steel sections up to 3 hour fire ratings for both interior and exterior environments.
    • Durable finish - provides a hard, durable finish resistant to normal wear.
    • Thin film coating - offers an economical solution to alternative fireproofing.
    • VOC compliant
    • Easy repair - if damaged it can be repaired easily using material as putty.

    Description:

    Thermo-Lag 2000-SP is designed to fireproof steelwork for up to a 3 hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, tubes, pipes, vessel skirts, bulkheads, underdecks and electrical raceways.


  • Thermo-Lag 220

    Features:

    • Class A fire hazard classification from ASTM E84 testing at Underwriter's Laboratories, Inc.
    • Durable finish - provides a hard, durable finish resistant to normal wear
    • Thin film coating
    • VOC compliant
    • Easy repair - if damaged, it can be repaired easily using a brush or roller

    Description:

    Thermo-Lag® 220 is designed to limit the spread of flame across interior wood substrates.


  • Thermo-Lag 270

    Features:

    • Flexible
    • Hard, dust free surface
    • Allows easy replacement of cables
    • Water-based product, low odor
    • Asbestos-Free – complies with EPA and OSHA regulations
    • Factory Mutual – tested and approved
    • Does not de-rate cables
    • Weathering – approved for exterior use
    • Quality Manufactured – under strict Carboline quality standards
    • Provides protection at 1/16” Dry Film Thickness

    Description:

    A water based mastic that can be applied to electrical cables to retard fire propagation. Once applied, it meets code and insurance requirements for interior and exterior use. It provides a hard and flexible surface that will not dust, flake, or spall.


  • Thermo-Lag 3000-A

    Features:

    • UL listed - designs for many types of steel sections up to 4 hour fire ratings for both interior and exterior environments.
    • Durable finish - provides a hard, durable finish resistant to normal wear.
    • Thin film coating - offers an economical solution to alternative fireproofing.
    • VOC compliant
    • Easy repair - if damaged it can be repaired easily using material as putty.

    Description:

    Thermo-Lag 3000-A is an architectural grade, 100% solids epoxy based intumescent designed to fireproof steelwork for up to a 4 hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, tubes, pipes, vessel skirts, bulkheads, underdecks and electrical raceways.


  • Thermo-Lag 3000-P

    Features:

    • UL listed - designs for many types of steel sections up to 4 hour fire ratings for both interior and exterior environments.
    • Durable finish - provides a hard, durable finish resistant to normal wear.
    • Thin film coating - offers an economical solution to alternative fireproofing.
    • VOC compliant
    • Easy repair - if damaged it can be repaired easily using material as putty.

    Description:

    Thermo-Lag 3000-P is a petrochemical grade, 100% solids epoxy based intumescent designed to fireproof steelwork for up to a 4 hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, tubes, pipes, vessel skirts, bulkheads, underdecks and electrical raceways.


  • Thermo-Lag 3000-SA

    Features:

    • UL listed - designs for many types of steel sections up to 4 hour fire ratings for both interior and exterior environments.
    • Durable finish - provides a hard, durable finish resistant to normal wear.
    • Thin film coating - offers an economical solution to alternative fireproofing.
    • VOC compliant
    • Easy repair - if damaged it can be repaired easily using material as putty.

    Description:

    Thermo-Lag 3000-SA is an architectural grade, 95% solids epoxy based intumescent designed to fireproof steelwork for up to a 4 hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, tubes, pipes, vessel skirts, bulkheads, underdecks and electrical raceways.


  • Thermo-Lag 3000-SP

    Features:

    • UL listed - designs for many types of steel sections up to 4 hour fire ratings for both interior and exterior environments.
    • Durable finish - provides a hard, durable finish resistant to normal wear.
    • Thin film coating - offers an economical solution to alternative fireproofing.
    • VOC compliant
    • Easy repair - if damaged it can be repaired easily using material as putty.

    Description:

    Thermo-Lag 3000-SP is a petrochemical grade, 95% solids epoxy based intumescent designed to fireproof steelwork for up to a 4 hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, tubes, pipes, vessel skirts, bulkheads, underdecks and electrical raceways.


  • Thermo-Lag 440-P

    Features:

    • UL listed - designs for many types of steel sections up to 4 hour fire ratings for both interior and exterior environments.
    • Durable finish - provides a hard, durable finish resistant to normal wear.
    • Thin film coating - offers an economical solution to alternative fireproofing.
    • VOC compliant
    • Easy repair - if damaged it can be repaired easily using material as putty.

    Description:

    Thermo-Lag 440-P is designed to fireproof steelwork for up to a 4 hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, pressurized and non pressurized spheres, tanks and railcars to provide hydrocarbon pool fire and jet fire ratings.


  • Thermo-Lag 440-SP

    Features:

    • UL listed - designs for many types of steel sections up to 4 hour fire ratings for both interior and exterior environments.
    • Durable finish - provides a hard, durable finish resistant to normal wear.
    • Thin film coating - offers an economical solution to alternative fireproofing.
    • VOC compliant
    • Easy repair - if damaged it can be repaired easily using material as putty.

    Description:

    Thermo-Lag 440-SP is designed to fireproof steelwork for up to a 4 hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, pressurized and non pressurized spheres, tanks and railcars to provide hydrocarbon pool fire and jet fire ratings.